background image

 

 
 
 

 

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change. 

© 

ESERA-Automation, E-Service GmbH 2019 

www.esera.de 

Programming Manual Controller-Gateway-Station V1.0 R1.1 

Page 77 of 77 

27. 

Conclusion and feedback 

During the development of the 1-Wire Controller / 1-Wire Gateway, we put a lot of effort into integrating as many 
practical aspects as possible from a user's point of view. As we are manufacturer and not the "end user", we 
certainly won’t succeed to 100%. Therefore, we would like you to send us your feedback, impressions, 
suggestions for improvement as well as error messages that have occurred in your environment by mail to 

support@esera.de

We would also be very pleased if you will leave product reviews at our online shop. 

 
Please recommend us also in various forum platforms. Our goal is to operate the 1-Wire bus as professional as 
possible and to establish it as a fixed standard in the field of IoT, Smart Automation and Smart Home. 
My special thanks go especially to all our test customers, who have taken a lot of time to test our 
1-Wire Controller / 1-Wire Gateway and to leave very constructive feedback. 

28. 

Warranty 

ESERA-Automation (E-SERVICE GmbH) guarantees that the goods sold at the time of transfer of risk to be 
free from material and workmanship defects and have the contractually assured characteristics. The statutory 
warranty period of two years begins from date of invoice. The warranty does not extend to the normal 
operational wear and normal wear and tear. Customer claims for damages, for example, for non-performance, 
fault in contracting, breach of secondary contractual obligations, consequential damages, damages resulting 
from unauthorized usage and other legal grounds are excluded. Excepting to this, ESERA-Automation accepts 
liability for the absence of a guaranteed quality resulting from intent or gross negligence. Claims made under 
the Product Liability Act are not affected. 
 
If defects occur for which the ESERA-Automation is responsible, and in the case of replacement goods, the 
replacement is faulty, the buyer has the right to have the original purchase price refunded or a reduction of the 
purchase price. ESERA-Automation accepts liability neither for the constant and uninterrupted availability of 
the ESERA-Automation or for technical or electronic errors in the online offer. 
  
We develop our products further and we reserve the right to make changes and improvements to any of the 
products described in this documentation without prior notice. If you need documentation or information about 
older product versions, contact us by email a

info@esera.de

 

29. 

Trademarks

 

All mentioned designations, logos, names and trademarks (including those which are not explicitly marked) 
are trademarks, registered trademarks or other copyright or trademarks or titles or legally protected 
designations of their respective owners and are hereby expressly recognized as such by us. The mention of 
these designations, logos, names and trademarks is made for identification purposes only and does not 
represent a claim of any kind on the part of ESERA-Automation, E-Service GmbH on these designations, 
logos, names and trademarks. Moreover, from their appearance on ESERA-Automation webpages it cannot 
be concluded that designations, logos, names and trademarks are free of commercial property rights. 
ESERA is a registered trademark of E-Service GmbH. 

30. 

Contact

 

ESERA-Automation, E-Service GmbH 
Adelindastrasse 20 
87600 Kaufbeuren 
GERMANY 
Tel.: +49 8341 999 80-0 
Fax: +49 8341 999 80-10 

www.esera.de

 

info@esera.de

 

WEEE-Number: DE30249510 

 
 

 

Summary of Contents for 1-Wire Controller 2














































































Reviews: