background image

All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of 
ESERA GmbH. Errors and technical modification subject to change. 



ESERA GmbH, ESERA-Automation 2020 

www.esera.de 

11324 V2.0 R1.0  Manual 

Page 8 of 8 

 
 
 
 

20 

Warranty 

ESERA GmbH guarantees that the sold goods are free of material and manufacturing defects at the time of transfer of risk 
and have the contractually assured properties. The statutory warranty period of two years from invoicing shall apply. The 
warranty does not cover normal wear and tear. Claims of the customer for damages, for example, for non-performance, fault 
in contracting, breach of secondary contractual obligations, consequential damages, damages resulting from unauthorized 
usage and other legal grounds are excluded.. Except for this, ESERA GmbH shall be liable in the absence of a warranted 
quality, in the case of intent or gross negligence. Claims from the product liability law are not affected by this. Should defects 
occur for which

 

ESERA GmbH is responsible, and should the replacement

 

delivery also

 

be defective in the case of exchange 

of the goods, the purchaser shall be entitled to conversion or reduction. ESERA GmbH accepts no liability for the constant and 
uninterrupted availability of ESERA GmbH nor for technical or electronic errors in the online offer. 
We are constantly developing our products further and reserve the right to make changes and improvements to any of the 
products described in this documentation without prior notice. If you need documentation or information about older versions, 
please contact us by e-mail a

info@esera.de

 

 

21 

Trademarks 

All listed designations, logos, names and trademarks, (also those which are not explicitly marked), are trademarks, 
registered trademarks or other copyrighted or brand or title protected designations of their respective owners and are 
expressly recognized by us as such. The naming of these designations, logos, names and trademarks is solely for 
identification purposes and does not represent any claim of ESERA GmbH to these designations, logos, names and 
trademarks. Furthermore, it cannot be concluded from the appearance on the ESERA GmbH webpages that designations, 
logos or names are free of industrial property rights. 

ESERA and Auto-E-Connect are registered trademarks of ESERA GmbH. 

 

22 

Contact 

ESERA GmbH  
Adelindastrasse 20 
87600 Kaufbeuren 
Germany 
Tel.: +49 8341 999 80-0 
Fax: +49 8341 999 80-10 

www.esera.de

 

info@esera.de

 

WEEE-Number: DE30249510

 

 

Summary of Contents for auto connect 11324









Reviews: