background image

 
 

1. READ INSTRUCTIONS 

All the safety and operating instructions should be read 
before the appliance is operated. 

2. RETAIN INSTRUCTIONS 

The safety and operating instructions should be retained 
for future reference. 

3. HEED WARNINGS 

All warnings on the appliance and in the operating 
instructions should be adhered to. 

4. FOLLOW INSTRUCTIONS 

All operating and use instructions should be followed. 

5. WATER AND MOISTURE 

The appliance should not be used near water – for 
example, near a bathtub, washbowl, kitchen sink, 
laundry tub, in a wet basement, or near a swimming pool, 
etc. 

6. CART AND STAND 

The appliance should be used only with a cart or stand 
that is recommended by the manufacturer. 
 

6A

. An appliance and cart combination 

should be moved with care. Quick stop, 
excessive force, and uneven surface 
may cause the appliance and cart 
combination to overturn. 

7. WALL OR CEILING MOUNTING 

This equipment is not designed for use mounted on a 
wall or a ceiling. 

8. VENTILATION 

The appliance should be situated so that its location or 
position does not inference with its proper ventilation. 
For example, the appliance should not be situated on a 
bed, sofa, rug, or similar surface that may block the 
ventilation openings, or placed in a built-in installation, 
such as bookcase or cabinet that may impede the flow of 
air through the ventilation openings. 

9. HEAT 

The appliance should be situated away from heat 
sources such as radiators, heat registers, stoves, or 
other appliances (including amplifiers) that produce heat. 

10. POWER SOURCES 

The appliance should be connected to a power supply 
only of the type described in the operating instructions or 
as marked on the appliance. 

11. POWER – CORD PROTECTION 

Power-supply cords should be routed so that they are 
not likely to be walked on or pinched by items placed 
upon or against them, paying particular attention to cords 
at plugs, convenience receptacles, and the point where 
they exist from the appliance. 

12. CLEANING 

The appliance should be cleaned only as recommended 
by the manufacturer. 

13. NON USE PERIODS 

The power cord of the appliance should be unplugged 

 
 
 
 
 
from the outlet when left unused for a long period of time. 

14. OBJECT AND LIQUID ENTRY 

Care should be taken so that objects do not fall and 
liquids are not spilled into the enclosure through 
openings. 

15. SERVICING 

The user should not attempt to service the appliance 
beyond that described in the operating instructions. All 
other servicing should be referred to qualified service 
personnel. 

 

 

16. DAMAGE REQUIRING SERVICE 

The appliance should be serviced by qualified service 
personnel when: 

a) 

The power-supply cord or the plug has been 
damaged; or   

b) 

Objects have fallen, or liquid has been spilled 
into the appliance; or 

c) 

The appliance has been exposed to rain; or 

d)  The appliance does not appear to operate 

normally or exhibits a marked change in 
performance; or 

e)  The appliance has been dropped, or the 

enclosure is damaged. 

 

17. POWER LINES   

(APPLIES FOR TUNER AND RECEIVERS ONLY) 
 
An outdoor antenna should be located away from power 
lines. 
 

 

SAFETY INSTRUCTION 

Summary of Contents for SW10K eXperience














Reviews: