73
Troubleshooting
Espressions VACU PRO 2
does not work
•
Make sure the power cable on the MAGIC VAC® is fully inserted in the machine and
in the electrical outlet. Check the electrical outlet by trying another device in the
same outlet.
•
Make sure the power cable and/or plug is not defective. If so, do not use the machine.
Espressions VACU PRO 2
does not perform the first
seal on the piece of cut roll
•
Check that the piece of cut roll is correctly positioned as described in the paragraph:
'5 - Making bags from MAGIC VAC® rolls'. Check the position and integrity of the
Sealing Gasket
Espressions VACU PRO 2
does not completely
vacuumpack the bags
•
In order to correctly seal the bags, the open end must be entirely inside the
Vacuum Chamber (8). Check the correct position through the Lit WINDOW (3).
•
Make sure the Sealing Bar(6), the Airtight Gasket (7) and Sealing Gasket (9) are not
dirty.
•
The MAGIC VAC® bag may be punctured. To check, seal the bag with air inside,
place it under water and squeeze. If you see bubbles, there is a leak. Reseal or use
another bag.
Espressions VACU PRO 2
does not seal the bag or
roll completely
•
When you can’t completely seal the bag, press the 'sealing mode' button (2M) and
increase the sealing time.
•
If the Sealing Bar (6) overheats and melts the bag, lift the Cover (5) and allow the
Sealing Bar (6) to cool for a few minutes.
•
Check the position and integrity of the Sealing Gasket (9)
•
If liquids escape during the vacuum-packing phase, remember that they must first
be refrigerated.
TIP:
Soup, marinades and other liquid items that you want to vacuum in a foil bag,
you can first freeze in a container and then remove and freeze frozen in a bag.
The Espressions MAGIC VAC®
bag doesn't maintain its
vacuum after sealing
•
Leaks along the seal can be caused by wrinkles, crumbs, grease or liquids. Open
the bag, clean the upper part of the inside of the bag and remove any residue from
the Sealing Bar (6) before resealing.
•
Make sure the bag is not punctured and thus did not maintain the vacuum.
Protect any pointed edges of the contents in the bag using paper napkins.
Espressions VACU PRO 2
does not seal containers.
•
Using the Canister Tube (16), connect the canister lid (or the Lid Attachment if
necessary) and the ACCESSORY PORT (4) on the machine.
•
Leave adequate space (at least 3 cm) between the contents and the top of the jar
or canister.
•
Make sure that the rim of the jar or canister and universal lid are not damaged in
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
•
Make sure the gasket on the canister lid or universal lid is placed in the correct
position and not damaged.
Espressions MAGIC VAC®
canisters or Espressions
MAGIC VAC® lids do
not maintain the seal
•
Make sure the knob on the canister lid is set to 'VACUUM' before vacuum-packing
and that it is set to 'CLOSED' after it is complete.
•
Check that the O-Ring under the knob on the canister lid or universal lid is correctly
positioned.
•
Makes sure that the rim of the jar or canister and universal lid are not damaged in
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
•
Make sure the gasket on the canister lid or universal lid is placed in the correct
position and not damaged.
•
Make sure the connection tube is correctly connected to both the canister knob as
well as the ACCESSORY PORT (4) on the machine.
Summary of Contents for EP6400
