background image

 

 

   

STEP 1: 

1. 

Join Rear Main Frame (100) and Front Main Frame (1) together and use 
Combination M5 Allen Wrench & Phillips Head Screw Driver (68) to tighten six 
5/16" × 3/4" Button Head Socket Bolts (32), six 5/16” spilt washes (35) together 
with six 5/16" Flat Washers (33). 

2. 

Locate the Console Mast (2) and slide on the Console Mast Cover (80). Make sure 
the cover is facing the correct direction, as shown below, before sliding onto mast. 
Install the wiring harness into the bottom of the mast and out the top. Be careful 
when installing the console mast to the mainframe so as not to pinch or cut the 
wiring harness, damage to the console may occur. 

3. 

Install the console mast on the mainframe using the M5 Allen Wrench (68) to 
tighten 5pcs of 5/16" × 3/4" Button Head Socket Bolts (32) , 4pcs of 5/16” Flat 
Washers (33) , 5pcs of 5/16” spilt washes (35) and 1pcs of 5/16" Curved Washer 
(34). Snap the Console Mast Cover (80) in place on the body of the bike.   

4. 

Connect the cable (93) to the Console Assembly (47) and install the console onto 
the Console Mast (2) using the Phillips Head Screw Driver (68) to tighten 4pcs of 
M5 × 12mm Phillips head screws (41). 

 

Assembly Instructions 

Summary of Contents for ESP0037 R6 Recumbent
























Reviews: