background image

 16

 

Fig.14 

 

 

 

 

CARE AND MAINTENANCE                                                  

To obtain the best performance from your heater make sure you perform the following 
maintenance activities on a regular basis: 
a. Abrasive cleaners will damage this product. 
b. Never use oven cleaner to clean any part of heater. 
c. Do not clean any heater part in a self-cleaning oven. The extreme heat will damage 

the finish. 

d. More frequent cleaning may be required as necessary. It is imperative that control 

compartment, burners and circulating air passageways of the heater be kept clean. 

e. Spiders and insects can create a dangerous condition that may damage heater or 

make it unsafe. Keep burner area clean of all spiders, webs or insects. Clean burner 
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away 
smaller particles. 

f. Inspect heater before each use. 
g. Have heater inspected annually and repairs should be made by a qualified service 

person. 

h. Check heater immediately if any of the following conditions exist. 

 

 

Fig.16

In any case of failure of normal ignition, please 
use the lighter (sold separately) to reach the 
burner for ignition through the hole on the 
bottom of burner diffuser. 
 
WARNING 
FOR YOUR SATETY: 
If at any time you are unable to light burner 
and smell gas, wait 5 minutes to allow gas to 
dissipate before attempting to light heater. 
 
WARNING 
FOR YOUR SATETY: 
DO NOT touch or move heater for at least 45 
minutes after use. Allow emitter and dome to 
cool before touching. 
 
CAUTION:   
Avoid inhaling fumes emitted from the heater’s 
first use. Smoke and odor from the burning of 
oils used in manufacturing will appear. Both 
smoke and odor will dissipate after 
approximately 30 minutes. The heater should 
NOT produce thick black smoke. 
 

Summary of Contents for 640-08477458-7




















Reviews: