14
V.3.0
Operating instructions
your product
V.3.0
Operating instructions
5
Operating instructions
BEFORE INSTALLING THIS PRODUCT, IT IS IMPORTANT TO READ AND UNDERSTAND THE
INSTALLATION INSTRUCTIONS COMPLETELY IN ORDER TO AVOID PHYSICAL INJURIES AND
MATERIAL DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN A PLACE WHICH IS EASILY
ACCESSIBLE SO YOU CAN CONSULT THEM AT A LATER DATE.
The safety instructions must be followed throughout the installation of this product. User safety
equipment and suitable tools for installation in order to avoid physical injury.
•
This appliance is intended for domestic use only
inside a dwelling place. Only use the appliance as
indicated in these operating instructions.
•
If the product were to be sold or given to another
person, make sure that the operating instructions
are passed on with it and that no parts are defective.
•
This wall mount bracket is able to support a
maximum load of 45 kg for screens with a diagonal
measurement of 32” (82 cm) to 75” (190 cm)
maximum. Ensure that the wall structure can
support such a load.
•
The weight of the screen must not exceed the
maximum load capacity of the bracket.
•
It is essential that you follow a correct installation
procedure. This must be carried out by two
qualifi ed people. Non-compliance with the installation
instructions may lead to severe physical injury, linked
to falling or incorrect handling of the screen.
•
Do not install the bracket on a structure which is
subject to vibrations, movement or which may be
subject to impacts. Non-compliance may lead to
the screen being damaged or the surface of the
bracket being damaged.
•
Do not install the bracket in a place of passage in
order to avoid knocks and injuries (above a bed, a
chair, a door or in a corridor…).
•
Do not install the bracket near heating, a fi replace,
direct sunlight, air-conditioning or other sources of
direct heat.
•
Non-compliance may lead to the screen being
damaged and may increase the risk of fi re.
•
Do not install the bracket in a very damp environment.
•
One month after installation, check that all the
screws are tight and that the wall plate has been
correctly attached to the wall. Stability may be
reduced once the TV is attached to the bracket.
•
Please note: Please check that no electric cables,
gas or water pipes are behind the wall onto which
you wish to fi x your bracket!
•
Stability may be reduced if the bracket is attached
to an item of furniture.
•
Check the position of the electric cables when you
install or handle the wall bracket, in order to avoid
any pinching or deterioration of the cables.
•
The screw fi xings supplied with this wall bracket
are intended exclusively for fi xing to a wall made
up of solid bricks or concrete.
•
For installation on any other medium (wood, hollow
bricks, plasterboard surfaces, steel…) please
contact an approved professional installer, and use
the appropriate equipment.
•
Before beginning installation, please check the
composition of your wall. Do not install the bracket
on old or badly sealed brickwork, on a plasterboard
surface or wood panelling.
•
Keep children away from the installation and
ensure that they cannot play with the appliance
subsequently.
•
The packaging material (packaging paper,
polystyrene) can be dangerous for children: there
is a risk of suffocation. Do not leave packaging
material within reach of children!
6
V.3.0
installation of wall plate
installation of wall plate
Begin by positioning the drilling template against the wall using the
provided spirit level to keep it straight.
Use adhesive or drawing pins to hold the template against the wall
while you drill six holes which will be used to attach the bracket.
The screw fi xings supplied with this wall bracket are intended exclusively for fi xing to a
wall made up of solid bricks or concrete. Please use all types of screws (depending on the
type of wall) for fi xing.
For installation on any other medium, please contact an approved professional installer,
and use the appropriate equipment
10mm
60mm
Drill the holes with an electric drill and a 10 mm concrete bit.
Remove the template and place to one side.
Insert a concrete rawl plug in each hole. If necessary, you can use a hammer to lightly tap each rawl
plug, so they are at the same level as the wall. Once the rawl plugs are in place, position the wall plate.
Attach the washers and then the lag screws into the rawl plugs which project slightly from the wall, as
indicated in the diagram below.
•
Do not tighten completely until all
the screws are in place.
•
Do not overtighten the screws. This
can damage the wall needlessly.
•
Do not release the wall bracket
before it is firmly attached to
the wall.
!
Summary of Contents for 8000790
