background image

ES5338.1 Carrier Board for Wheel Speed Sensor Simulation - User’s Guide

26

Design, Installation and Fuses

ETAS

Installation of the ES5338.1 Carrier Board in the ES5300.1-A Housing or 
ES5300.1-B Housing

1. Ensure that ESD-compliant conditions exist at your 

workplace.

2. Shut down the real-time PC and switch off the 

power supply of the ES5300.1-A or ES5300.1-B 
using the switch at the rear of the housing.

3. Wait a few minutes for the components (capacitors, 

etc.) to be discharged.

4. Insert the ES5338.1 Carrier Board (handle at the 

front plate must point down!) into the upper and 
lower rail of the slot and push it in a little bit.

5. Carefully push in the carrier board until the back-

plane connector of the ES5338.1 Carrier Board is 
completely inserted in the socket of the backplane.

6. Secure the carrier card by fastening the front plate 

with screws.

7. Install front plates at all open slots before starting 

up the ES5338.1 Carrier Board.

CAUTION!

If correctly installed, the ES5338.1 Carrier Board occupies only one 
slot of the ES5300.1-A Housing or the ES5300.1-B Housing. 
If neighboring boards or cover slots collide with the ES5338.1 Carrier 
Board, then the combination of PB5338CURR.1-A and ES5338.1 
Carrier Board is not correctly installed.
Observe "Assembly of the PB5338CURR.1-A Piggyback on the 
ES5338.1 Carrier Board" on page 24.

CAUTION!

The air circulation inside the ES5300.1-A Housing or the ES5300.1-B 
Housing can be ensured only if all free slots are covered with front 
plates. Otherwise, it may lead to overtemperatures and trip the over-
temperature protection of the ES5300.1-A Housing or ES5300.1-B 
Housing. For this reason, install front plates in all free slots!

Note

Watch for cables in the insertion area while pushing 
in the board – pull the lines to the front door area if 
necessary.

Summary of Contents for ES5338.1













































Reviews: