background image

ETC Installation Guide

ArcSystem Pro Multi-Cell

ArcSystem Pro Multi-Cell

Page 2 of 24

ETC

Compliance

ArcSystem Multi-Cell Standard Fixtures with Integral Drivers

Model

Description

Compliance

ARCP2

100–240 V or 100–277 V Pro Two-Cell

cULus Listed

ANSI/UL Std. 1598

CAN/CSA 22.2 No. 250.0

FCC part 15 class A

CE Certified

ARCP2RDM

100–240 V or 100–277 V Pro Two-Cell RDM

ARCP4L

100–240 V or 100–277 V Pro Four-Cell Linear

ARCP4LRDM

100–240 V or 100–277 V Pro Four-Cell Linear RDM

ARCP4S

100–240 V or 100–277 V Pro Four-Cell Square

ARCP4SRDM

100–240 V or 100–277 V Pro Four-Cell Square RDM

ARCP4R

100–240 V Pro Four-Cell Round

ARCP4RRDM

100–240 V Pro Four-Cell Round RDM

ARCP8

100–240 V or 100–277 V Pro Eight-Cell

ARCP8RDM

100–240 V or 100–277 V Pro Eight-Cell RDM

ArcSystem Multi-Cell Emergency Fixtures with Integral Drivers

Model

Description

ARCPE2

100–240 V or 100–277 V Pro Two-Cell Emergency

cULus Listed

ANSI/UL Std. 924

CAN/CSA C22.2 No. 141

FCC part 15 class A

CE Certified

ARCPE2RDM

100–240 V or 100–277 V Pro Two-Cell RDM Emergency

ARCPE4L

100–240 V or 100–277 V Pro Four-Cell Linear Emergency

ARCPE4LRDM

100–240 V or 100–277 V Pro Four-Cell Linear RDM Emergency

ARCPE4S

100–240 V or 100–277 V Pro Four-Cell Square Emergency

ARCPE4SRDM

100–240 V or 100–277 V Pro Four-Cell Square RDM Emergency

ARCPE4R

100–125 V Pro Four-Cell Round Emergency

ARCPE4RRDM

100–125 V Pro Four-Cell Round RDM Emergency

ARCPE8

100–240 V or 100–277 V Pro Eight-Cell Emergency

ARCPE8RDM

100–240 V or 100–277 V Pro Eight-Cell RDM Emergency

Summary of Contents for ArcSystem ARCP2

























Reviews: