background image

ETC Installation Guide

SmartSwitch to Echo Relay Panel Feedthrough Retrofit Kit

SmartSwitch to Echo Relay Panel Feedthrough Retrofit Kit

Page 5 of 14

ETC

Remove the User Interface

1. Using the Phillips screwdriver, remove the two M5 screws securing the I/O panel below the 

Smartswitch User Interface. The panel should now open by folding downward.

2. Remove the ground wire from the spade on the I/O card.

3. Disconnect all other cable connections that are preventing the panel from being removed.

4. Label all remaining wires.

5. Remove the I/O panel. This panel is no longer needed and can be discarded.

6. Remove any remaining adhesive-back cable mounts.

7. Remove the four 8-32 x 3/8 inch screws that secure the User Interface to the rear of the SmartSwitch 

enclosure. Set the screws aside; they will be reused to secure the new User Interface to the same 
location in the panel.

8. Remove the User Interface from the SmartSwitch panel. The User Interface is no longer needed and 

can be discarded.

v

v

v

Ribbon cable

RJ45 to upper relay 
control card

RJ45 splitter board 
(in 48 circuit panel 
only)

I/O panel 
ground to 
chassis

LinkPower 
supply
Data communication 
to CPU

Emergency/SmartLink

DMX In

DMX Pass-Thru

ESD drain wire 
ground

Summary of Contents for ERP24-FT















Reviews: