manualshive.com logo in svg

ETC LIGHTHACK BOX 1, Assembly Instructions Manual

Get your ETC Lighthack Box 1 up and running with our easy-to-follow Assembly Instructions Manual. Download the manual for free from 88.208.23.73:8080 and access step-by-step guidelines to set up your box effortlessly. Ensure a smooth installation process and maximize the potential of your lighting system with our comprehensive manual.

Share
Download
background image

9 

 

 

22. Line up the Arduino with a side of the box in order to estimate the location of the hole. 

We've found a good location to be 1"/25mm in from a corner and ½"/12mm up from the 
bottom. Use a ½"/12mm drill bit to drill a hole for the USB  connector. Make sure you can 
connect a USB  cable to your Arduino through the hole. 

23. Drill a hole for the USB  connector. If desired, add a second 1/2" hole to mount the 

potentiometer. 

 

 

 

Summary of Contents for LIGHTHACK BOX 1


















Reviews:

No comments

Related manuals for LIGHTHACK BOX 1

PASCO ES-9070 Instruction Manual And Experiment Manual preview
ES-9070
Brand: PASCO Pages: 22
Life form LF03611U Instruction Manual preview
LF03611U
Brand: Life form Pages: 7

Brands by name

Popular brands

Load more brands