background image

Table of Contents

ETC® and Source Four Mini™ are either registered trademarks or trademarks of Electronic 
Theatre Controls, Inc. in the United States and other countries.

ETC permits the reproduction of materials in this manual only for non-commercial 
purposes. All other rights are reserved by ETC.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Install Lens Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Terminate 12V Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Adjusting the yoke position . . . . . . . . . . . . . . . . . . . . . . .4

Setting the angle with the yoke . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Focusing the beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Shaping the Beam  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Pattern Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Color Frame Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using a C-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Replacing the Lamp  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Cleaning the Glass Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Summary of Contents for Source Four Mini LED













Reviews: