background image

6  • Source Four MultiPAR

Circuit wiring configurations for the MultiPar-12.

The Source 4 MultiPAR can be wired for 3 circuit or 4 circuit configurations. Before changing the configuration, make 
sure that you have sufficient power (dimmer capacity) to operate the fixture. There are four terminal blocks inside the 
unit to place wiring. Each terminal block has four lead connection points. All of the hot and neutrals are labeled with 
a number for your convenience.

Three circuit configuration

1.

Disconnect power before changing the wiring.

2.

Loosen the captured screw on the back of the raceway and open the raceway lid.

3.

In the first terminal block on the left, insert the wires labeled 1,4,7,10. 

4.

In the second terminal block from the left, insert the wires labeled 2,5,8,11.

5.

In the third terminal block from the left, insert the wires labeled 3,6,9,12

6.

The fourth terminal block from the left is not used and is left empty.See 

Figure 7

 for detail.

Figure 7

Four circuit configuration

1.

Disconnect power before changing the wiring.

2.

Loosen the captured screw on the back of the raceway and open the raceway lid.

3.

In the first terminal block on the left, insert the wires labeled 1,5,9

4.

In the second terminal block from the left, insert the wires labeled 2,6,10.

5.

In the third terminal block from the left, insert the wires labeled 3,7,11.

6.

In the fourth terminal block from the left, insert the wires labeled 4,8,12. Se

Figure 7

 for detail.

ORDER DIRECTLY TODAY AT: 

www.BulbAmerica.com

 or CALL TOLL FREE 888-505-2111 

Summary of Contents for Source Four MultiPAR









Reviews: