background image

1

G

SM/GPRS

Modem User's Manual

Chapter 1

GS

0/G35S Modem Overview

Chapter 1

GS

M

/G

PRS

Modem Overview

1. 1 Product Description

G

SM/GPRS

Modem is a industrial external MODEM which can transmit

data based on GPRS (General Packet Radio Service). Self-contained E-
GSM/GSM-GPRS

 85

0/1

9

00 dual-band. Give your full 2.5G GSM/GPRS Voice

and data application. It also provides the function of USSD data terminal. Housed
in a rugged metallic casing, the modem is build to withstand the toughest
environments applications such as power plant control and outer door data

gathering.

1. 3 Product Features

Dual Band GSM/GPRS (GSM

85

0/1

9

00M

H

z)

Compatible to ETSI GSM Phase 2+

1.31 Product standard

1.32 Voice function

Telephony and Emergency calls
Full rate, enhanced full rate and half rate (FR/EFR/HR)
Echo canceling and noise eliminating
Speakerphone

Dual tone multi frequency function (DTMF)

1.33 Data Function

GSM Data/Fax features:

Data circuit asynchronous, transparent and non transparent up to 14,400 bits/s
Automatic fax group 3 (Class 1 and Class 2)

GPRS Data/Fax features

It Cannot Be Applied in TD-8012

Coding schemes: CS1 to CS4
PBCCH support

Model

TD-8011
TD-8012
TD-8013
TD-8014

Channel

Circuit Channel
CLASS 2
CLASS 10
CLASS 10

Rate

14.4K
28.8K
48K
48K

IP Function

None
None
None

Available

1. 2 Product Features

Summary of Contents for TD-8011















Reviews: