ETEKCITY MSR-C600 User Manual Download

Page: 5 / 16

- 4 -

The Meter Structure

( Figure 1)

1. Input Terminals

2. LCD Display

3. Functional Buttons

4. Rotary Switch

5. Trigger: Push/release it to open/close the clamp jaw.

6. Hand Guards: to protect user’s hand from touching

the dangerous area.

7. Transformer Jaws: designed to pick up the AC current

flowing through the conductor. It could transfer current

to voltage.

Rotary Switch

Below table indicated for information about the rotary switch positions.

Functional Buttons

Below table indicated for information about the functional button operations.

Rotary switch

positions

Function

DC voltage measurement
AC voltage measurement
Resistance measurement
Continuity/diode test

Power is turned off.

OFF

AC current measurement from

0.001A to 400A

2/20A

200/400A

Press

HOLD

to enter and exit the

Hold mode in any mode, the Meter beeps.

HOLD

MAX

Press

MAX

to start recording and updating

of maximum values.

SELECT

Press

SELECT

button to switch between

and

Summary of Contents for MSR-C600

















Search results

Summary of Contents for MSR-C600

Reviews:

Related manuals for MSR-C600

Brands by name

Popular brands

ETEKCITY MSR-C600, User Manual

Search results

Summary of Contents for MSR-C600

Reviews:

Related manuals for MSR-C600

Brands by name

Popular brands