READ THIS FIRST:
check the pack and make sure you have all of
the parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken
when assembling, fitting or handling to prevent
personal injury or damage to the product.
This light fitting must be installed by a
competent person in accordance with the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(BS7671).
The Building Regulations may be
obtained from oPsI (office for Public sector
Information) or the department of communities
and local Government and viewed and
downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this fitting
is fit for the purpose for which you have intended
it. Eterna lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British standard
and is intended for normal domestic service. Use of
this fitting in any other environment, for example
where prolonged periods of use may be expected
and/or higher than normal ambient temperatures,
may result in a foreshortened working life.
The lamps (tubes), supplied with this fitting are
consumable parts and therefore may be outside of
any warranty offered.
This fitting is not suitable for frequent use for
extended periods or in environments with higher
than normal ambient temperatures for example:
lighting public or shared spaces or in care facilities.
switch off the mains before commencing
installation and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Disconnect the hf ballast from the electrical supply
before flash or high voltage testing.
suitable for indoor use only.
This product is suitable for use in living areas. It
is not suitable for bathroom or other areas where
contact with moisture is likely.
This product is suitable for installation on surfaces
with normal flammability (indicated by the “f” in a
triangle) e.g. wood, plasterboard, masonry. It is not
suitable for use on highly flammable surfaces (e.g.
polystyrene, textiles).
Before making fixing hole(s), check that there are
no obstructions hidden beneath the mounting
surface such as pipes or cables.
Make sure that the fixings are strong enough to
support the weight of the fitting and hold it rigidly.
When choosing the location for your new fitting,
give consideration to the ease and frequency of
lamp changes. The fitting should not be installed in
a position where it will be difficult to reach,
Do not cover the fitting.
The fitting must be positioned so that there is at
least 10mm between the diffuser and any other
surfaces.
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(Bs7671).
This product is designed for permanent connection
to fixed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp McB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit. We recommend that the supply
incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
live - Brown or Red
neutral - Blue or Black
This fitting is double insulated; do not connect any
part to earth.
This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using
it safely.
small children should be supervised to ensure that
they do not play with this appliance.
ImPORTANT
- Always switch off and isolate mains
supply to the fittings before changing the lamp(s).
If the external flexible cable of this luminaire is
damaged it shall be exclusively replaced by an
qualified personnel.
you are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specified in the Wiring Regulations
(Bs7671) referred to in the Building Regulations.
874/2012
A
MODELNO.
LFT5 8W/13W
874/2012
A
+
MODELNO.
LFT5 21W/28W
MODELNO.
A
++
XXX
kWh/1000h
8.80
8W
A
MODELNO.
A
++
XXX
kWh/1000h
14.30
13W
A
MODELNO.
A
++
XXX
kWh/1000h
22.66
21W
A
+
MODELNO.
A
++
XXX
kWh/1000h
30.69
28W
A
+
