Model:
WP51SDEM3 / WP61SDEM3
IP65 LED Emergency Step Dim Weatherproof Fittings
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
INSTALLATION INSTRUCTIONS
A guide for qualified electricians
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit our website:
www.eterna-lighting.co.uk
Made in China
Issue 0918
PACK CONTENTS:
LED weatherproof fitting
FIXING KIT:
2 x Hanging clips
2 x Hanging hooks
1 x Grommet
1 x IP65 gland
2 x Wall plugs
2 x Fixing screws
2 x Washers
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” effective August 2005—UK
WEEE Regulations effective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST - DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Disconnect the power and clean the exterior only of
this fitting with a moist (not wet) cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specific
instructions regarding individual installations.
LAMP REPLACEMENT:
INDUSTRIAL BATTERIES:
Within certain products Eterna Lighting Ltd places lead
acid, lithium ion, nickel cadmium & nickel metal hydride
batteries on the market. Industrial batteries are subject
to waste regulation under the Waste Batteries and
Accumulators Regulations 2009 and should be disposed
of responsibly. Purchasers may be able to dispose of their
waste industrial batteries locally via legitimate licensed
trade waste contractors. Eterna is obliged to take back,
free of charge and within a reasonable time, waste
industrial batteries of the same chemistry supplied to a
Purchaser, for treatment and recycling and is required
to do this in any calendar year new industrial batteries
are placed on the market. In certain circumstances, this
may include batteries not originally supplied by Eterna.
If any Purchaser requires Eterna to take back Industrial
batteries, they should write to the Operations Director,
Eterna Lighting Ltd, Huxley Close, NN8 6AB, who will
then advise on the necessary arrangements for the
receipt, proper treatment and recycling of, the waste
industrial batteries.
BATTERY REPLACEMENT:
If after routine operation check, the lamp does not
remain lit for the three hour period, a new battery pack
may be required.
01. Switch off the electricity at the mains (both
permanent live and switch live) and allow batteries
to fully discharge then reconnect to supply and allow
charging for 24 hours.
02. Test again for 3 hours, if light does not remain lit, then
change the battery pack as follows:
03. Remove the diffuser and remove the gear tray.
04. Remove the battery case from the gear tray, then
remove the four screws and remove the battery by
unplugging the battery lead from the circuit board.
05. Write current date on the new battery pack and fit a
new battery by reversing the above procedure.
06. Plug battery pack into circuit board.
07. Refit gear tray and diffuser.
08. Restore power and allow charging for 24 hours.
09. Perform full operation check and update test record.
REPLACEMENT BATTERY TYPE:
Ni-Cd 6V 2000mAh
The light source contained in this luminaire
shall only be replaced by the manufacturer,
service agent or a similar qualified person.
CAUTION, RISK OF ELECTRIC SHOCK.
The light source is designed to last the lifetime of the
luminaire.
3 HOURS DURATION IN EMERGENCY MODE
