background image

  

1 / 16

SPT-DPFC1PH_EN-MAN_3.2_14-02-2014 - FW 12.9 / 9.6

TECHNICAL MANUAL OF INSTALLATION

INDEX

1

.

BUTTONS AND INDICATION LEDs                                                                                               > Pg. 2

2

.

DESCRIPTION                                                                                                                                  > Pg. 2

3

.

OPERATION                                         

                                                                         > Pg. 2

4

.

ELECTRICAL DIAGRAM FOR INSTALLATION                     

                                     > Pg. 3

5

.

SET-UP MENU                                                                                                     

                     > Pg. 4

6

.

SETTING PASSWORD                                                                                                                     > Pg. 7

7

.

SETTING AUTORECOGNIZED CAPACITOR BANK                                                                       > Pg. 7

8

.

MEASUREMENTS FUNCTIONS                                                                                                      > Pg. 8

9

.

COS

MM

AND SENSITIVITY SET-UP                                                                                                   > Pg. 9

10

.

OPERATION MODE                                                                                                                          > Pg. 9

11

.

ALARMS TABLE                                                                                                                               > Pg. 10

12

.

TECHNICAL DATA                                                                                                                          > Pg. 11

13

.

TERMINAL CONNECTIONS                                                                                                             > Pg. 15

14

.

DIMENSIONS                                                                                                                                    > Pg. 15

AVAILABLE OPTIONAL COMMUNICATION MODULE PC-USB / RS485 / TTL - ORDER CODE: SCUSB485
REGISTERS MODBUS-RTU TABLE ON REQUEST

       

!!! IMPORTANT !!! READ THE INSTALLATION MANUAL BEFORE USE.

            THE SAFETY OF THE PRODUCT IS STRICTLY RELATED TO ITS USE THAT HAS

                         TO BE DONE AS SPECIFIED BY THE MANIFACTURER.

I

POWER FACTOR CONTROLLER

PFC6DA             PFC8DB             PFC12DB

ETI Elektroelement d.d. - Slovenija

Tel.: 03/56-57-570- Fax: 03/56-74-077

www.eti.si - eti@eti.si

Summary of Contents for 004656570

















Reviews: