Package contents
Part Description
Quantity
A
Fixture
1
B
Mounting Chain
2
C
Hook Screws
2
D
Plastic Drywall
Anchors
2
Hardware not shown to actual size.
NOTE
:
Keep your receipt and these instructions for proof of purchase.
WARNING
:
RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are
working on is shut off. Either remove the fuse or turn off the circuit breaker before
removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a
qualified electrician to do the installation.
InstaLLatIon
CAUTION:
When suspension mounting, make sure the light fixture is located directly
below the electrical outlet.
NOTE:
Installing contractor is responsible for selecting a suitable location that can
support the weight of the fixture and determining the method for mounting the fixture
before installing, based on the type of ceiling.
Shut off power at the electrical panel before beginning the installation.
Remove fixture and set aside to recycle in accordance with local requirements.
A
WARNING:
Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire,
or other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. •
Use the hook to support the chain, not the electrical cord. • Do not install on a radiant-heating type ceiling. • The unit is intended to be installed directly beneath a ceiling-mounted
receptacle, and that excess cord should be kept out of the workspace, such as by securing it to one of the supporting chains with a cable tie.
NOTICE:
The maximum distance to the electrical receptacle is determined by the 7.5 ft. power cord length.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment
into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Not for emergency lighting.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
If mounting to drywall:
Drill two 1/4in. holes in the ceiling.
Install the drywall anchors and the hook screws in each drilled
mounting holes.
If mounting to wood:
Drill two 1/16in. pilot holes in the ceiling.
Fasten the combo wood-machine (not included) end into the
hook screw (not included). Tighten the hook screw and make
sure it is secure.
NOTE:
Distance between 2 holes is 30 in.
NOTE:
If using eye hooks in the ceiling instead, two optional
S hooks are provided for hanging the fixture.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
UsE ANd CARE GUIdE
LEd sHOP LIGHT WITH BLUETOOTH
®
sPEAKERs
Model # 55703142
Part # sH-42IN-3600LM-8-40K-sV-BT
Certification # 55703142
1
2
3
Attach the S hooks that are at the bottom of
the mounting chains to the fixture. Use pilers
to close the S hooks and make sure the fixture
is secure.
4
Attach the mounting chains to the hooks that
were installed in the ceiling.
Adjust chains to level the fixture.
CAUTION:
The fixture must hang at least 3 in.
from the ceiling.
CAUTION:
Excess cord must be secured
to the mounting chain with cable ties (not
included).
NOTE:
If using eye hooks in the ceiling instead
of hooks then secure 2 S hooks (not included) to
the end of the mounting chain and attach the S
hooks to the eye hooks. Use pliers to close the
S hooks.
5
Plug the fixture into an electrical outlet.
Restore power to the electrical box.
Pull the chain down to turn activate the fixture.
7
connect to BLUetootH
®
WIReLess tecHnoLogY
1. When the fixture is plugged in, the speakers will emit a brief series of tones to indicate that the speakers
have power.
2. Enable Bluetooth
®
on your smart device.
3. Wait for the smart device to detect the fixture and then select it to pair the device to the speakers. When
successfully paired, the speakers will emit a brief series of tones to indicate that your device is connected.
4. Play music from your device while connected to the fixture to enjoy sound from the Bluetooth
®
speakers.
5. Turn off music on your smart device, disconnect the fixture from Bluetooth
®
on your smart device, or disable
Bluetooth
®
functionality on your smart device when sound is not wanted from the fixture.
NOTE:
Bluetooth
®
enabled smart devices typically have a range of approximately 33 ft. Attempting to pair
your smart device to the Bluetooth
®
speakers beyond the intended range can result in poor audio quality, drop-
outs, or failure to connect.
NOTE:
Only one device at a time can be connected to the Bluetooth
®
speakers.
B
C
Drywall
Wood
C
B
A
C
B
Hook
A
Plug
8
9
6
D
D
C
