6
1. Display
2. Unit selection button
3. (-) Button
4. ON/OFF button for LED light
5. ON/OFF button for compressor
6. (+) Button
7. LED light
8. Connector for the air hose
9. USB port
10. ON/OFF button for USB connection
11. Charging port
12. Charging indicator light
13. USB port indicator light
14. Air hose
15. Adapter for bicycle valves
16. Adapter for balls
17. Universal adapter for leisure items
18. Storage case
19. Plug-in charger
20. Charging indicator light
21. Charging cable
Figure 1: Overview
6. OPERATING INSTRUCTIONS
6.1 OVERVIEW
Figure 2: Overview of accessories
Insert the charging cable (position 21 in the overview) of the
plug-in charger (position 19 in the overview) into the charging port
of the compressor (position 11 in the overview). Plug the charger
into a mains socket. The charging indicator light (position 12 in the
overview) will now light up. During the charging process the charging
indicator light on the plug-in charger (position 20 in the overview) will
be red. When the compressor’s battery is fully charged, the indicator
light will be green. It takes approximately 4 hours to charge an empty
battery.
After charging, fi rst pull the plug-in charger out of the mains
socket and separate the compressor from the charging cable.
Always maintain this sequence.
6.2 CHARGING THE POWER PACK
Setting the target pressure
Press the button for selecting the unit (position 2 in the overview).
This will activate the display light. You can set the pressure unit by
continuing to press the button:
PSI -> BAR -> KGF/CM²
With the (-) and (+) buttons (position 3 and 6 in the overview) you
can set the target pressure. After you have set the pressure, press the
unit selection button once more, and the display will now show 0.00
again in the chosen unit.
Connecting the air hose
Screw the end of the air hose with the external thread (position 14
in the overview) into the compressor’s connector (position 8 in the
overview).
Using the adapter
If you would like to fi ll a tyre with an auto valve (Schrader valve), you
will not require an adapter. Screw the end of the air hose with the
internal thread onto the valve. Now you can switch on the
ompressor and fi ll the bicycle tyre.
Bicycle valve adapter (for Dunlop and Sclaverand valves) (15):
For Sclaverand valves: Undo the knurled screw of the valve piston and
push down briefl y once.
Screw the valve adapter, using the knurled crown, down onto the
bicycle valve.
Screw the end of the air hose with the internal thread onto the
adapter. Now you can switch on the compressor and fi ll the bicycle
tyre. After you have fi nished fi lling the tyre, detach the air hose and
the adapter from the valve.
For Sclaverand valves: Tighten the knurled screw of the valve piston
up again.
Adapter for balls (16):
Screw the adapter for balls into the internal thread of the air hose.
Insert the adapter into the valve of the ball. Now you can switch on
the compressor and fi ll the ball.
Universal adapter for leisure items (17):
Screw the universal adapter into the internal thread of the air hose.
Insert the universal adapter into the fi lling connection of your
leisure equipment. Depending on version, it is possible that the
universal adapter will need to be held fi rmly during the fi lling process.
Now you can switch on the compressor and start the fi lling process.
6.3 OPERATING THE COMPRESSOR
Checking the charge status
Press the button for selecting the unit (position 2 in the overview).
This will activate the display light. The battery symbol
indicates the charge status (empty, 25%, 50%, 75%, 100%).
Filling process
To start the fi lling process press the compressor’s ON/OFF button (po-
sition 5 in the overview).
The compressor will start, during the fi lling process the pressure will
appear on the display.
When the set target pressure has been reached the compressor will
switch itself off . Press the ON/OFF button once more.
Only leave the compressor operating
uninterrupted for a maximum for 5 minutes.
Allow the compressor to cool down for at least
15 minutes afterwards before using it again.
