background image

1. To  use accessories remove hose from rear of

cleaner by lifting up and twisting.

2. Place desired accessory onto end of hose or wand.

Turn ridge end to center.

Push wands together.

Grasp both wands near ridges.

Dusting/Upholstery Brush

 is for furniture, blinds, books, lamp

shades, shelves, curtains, draperies, cushions and fabrics.

Crevice Wand

 cleans corners, stairs, baseboards, and between

cushions.

Nested extension wands

 to add reach.

Pull apart.

9

HO
W T

O

 USE

ON/OFF Switch. International symbol I means On,

International symbol O means Off.

Cleaner Height Setting. An adjustment

that raises or lowers the cleaner base
to match the type of floor surface. With
the cleaner cord unplugged, set the
adjustment to lowest setting for
maximum carpet cleaning. If the
cleaner is difficult to push, move
adjustment to next highest setting
until cleaner is comfortable to
push.
 The brush roll must reach the carpet for effective cleaning. For ease in moving the adjustment
knob, place handle in operating position and tilt cleaner back to remove weight from front wheels.

Handle Release. Step on

handle release to pull
handle back to a
comfortable operating
position. To  lower
handle completely to
the floor, depress
handle release a
second time.

Dusting/

Upholstery

Brush

Crevice

Wand

Hose

or

Wand

Store

Operate

Clean

Under

WARNING: Avoid injury. Keep loose clothing, hair,

fingers, and all other parts of body
away from any moving part (such as
the revolving brush). Turn off the
switch and unplug the cleaner before
changing the cleaner height setting.

Helpful Information:

Before cleaning under low
furniture, check area first for
objects that might harm the
unit or block the vacuum
hose.

NOTE: While using accessories, do not place

cleaner on furniture or steps as the brush
roll may cause damage. Place cleaner on
floor with the handle in storage position.

Summary of Contents for 5740 series





















Reviews: