background image

OWNER’S MANUAL
MANUAL DEL PROPIETARIO
MANUEL D’INSTRUCTION

Model / Modelo / Modèle 998B

Dressmaker

®

For information or assistance:

Para más información o asistencia:

Pour plus d’information ou pour obtenir de l’assistance :

EURO-PRO

 

 Operating LLC

U.S.: 

21 Lawrence Paquette Ind. Dr.

    Canada: 4400, Bois-Franc

                      Champlain, NY 12919                       

     

    St-Laurent, QC H4S 1A7

Tél. : 1-

800-361-4639

EURO-PRO Operating LLC

 - All rights reserved

EURO-PRO Operating LLC

 - Tous droits réservés

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, safety precautions should always be followed,
including the following:
Read all instructions before using this sewing machine.

Danger

 - To reduce the risk of electric

shock:
1. An appliance should never be left
    unattended when plugged in or with
    batteries in place.
2. Always unplug this appliance from
    the electrical outlet and/or remove
    batteries immediately after using
    and before cleaning.

Warning

 - To reduce the risk of burns,

fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy.
    Close attention is necessary
    when this appliance is used by or
    near children.
2. Use this appliance only for its
    intended use as described in this
    manual. Use only attachments
    recommended by the manufacturer
    as contained in this manual.
3. Never operate this appliance if it has
    a damaged cord or plug, if it is not
    working properly, if it has been
    dropped or damaged, or dropped
    into water. Return the appliance to

    EURO-PRO Operating LLC

 

  

for

    examination, repair, electrical or
    mechanical adjustment.
4. Never operate the appliance with
    any air openings blocked. Keep
    ventilation openings of the sewing
    machine and foot control free from
    accumulation of lint, dust and loose
    cloth.

5. Keep fingers away from all moving
    parts. Special care is required
    around the sewing machine
    needle.
6. Always use the proper needle
    plate. The wrong plate can cause
    the needle to break.
7. Do not use bent needles.
8. Do not push or pull fabric while
    stitching. It may deflect the needle
    causing it to break.
9. Switch the sewing machine off
    when making any adjustments in
    the needle area, such as threading
    needle, changing needle,
    threading bobbin or changing
    presser foot.
10.Always unplug sewing machine
    from electrical outlet when
    removing covers, lubricating or
    when making any other user
    servicing adjustments mentioned
    in the instruction manual.
11.Never drop or insert any object
     into any opening.
12.Do not use outdoors.
13.Do not operate where aerosol
     (spray products) are being used or
     where oxygen is being
     administered.
14.To disconnect, turn all controls to
     the off position, then remove plug
     from outlet.
15.Do not unplug by pulling on cord.
     To unplug, grasp the plug, not the
     cord.

SAVE THESE INSTRUCTIONS

This sewing machine is intended for household use only.

1

Rev. 06/02

C

EURO-PRO

 

Operating LLC

All rights reserved

Summary of Contents for Dressmaker 998B















Reviews: