background image

12 

 

3.

    

Preparation & adjustment

 

 

3.1 Assembly  

 

WARNING: 

To reduce the risk of injury, turn machine off and disconnect from power source 

before installing and removing accessories, before adjusting or changing set- ups or when 
making repairs. Be sure all switches are in the OFF position. An accidental start-up can cause 
injury. 

 

Fitting the feed handles  

1.

 

Fit each of the three feed handles by screwing them into the hub in clockwise direction; 

2.

 

Tighten firmly by hand. 

 
The handles are supposed to face slightly outward. Be careful not to cross-thread any of the 
components. 

 
Mounting the safety guard 

The safety guard protects against chippings and accidental contact and must always be mounted 
before operation: 

1.

 

Hold the guard in front of the magnet, align the slots in the guard with the holes in the 

magnet; 

2.

 

Fit the screws into the holes located in the side of the magnet. 

 
WARNING: 

Always use the safety guard. 

 

 
 
Fitting the lubrication system 

The lubrication system can only be used for horizontal drilling (the 
drill being used vertically). 
 

 

1.

 

Hang the tank (A) on the tank holder; 

2.

 

Position and tighten the attachment pin (B); 

3.

 

Connect the hose (C) to the fitting on the gearbox. Make 

sure the hose is connected fully and tightly; 

4.

 

To disconnect the hose, press the blue ring on the 

connection and gently pull out the hose. 

 
 

[image 3-1] 

 
In order to use the lubrication system, it must be filled with a sufficient amount of cutting fluid. 

1.

 

Make sure the flow regulator is closed; 

2.

 

Unscrew the cap; 

3.

 

Fill the container with cutting fluid; 

4.

 

Screw the cap back on. 

 

Summary of Contents for ECO.40/2+


































Reviews: