17
INGLESE
Components
Power “On” Light (amber):
This light will illuminate when
the unit is plugged into the 230V~ wall outlet and will
remain on until the unit is unplugged.
CAUTION:
Read the instructions for “Filling the Water
Tank” before opening the Safety Cap.
Always depress
hand grip steam trigger until all pressure/ steam has
been vented from boiler.
CAUTION:
Always unplug before filling.
IMPORTANT:
Do
NOT
add cleaning solutions, scented
perfumes, oils or any other chemicals to the water used in
this appliance.
Use tap water or distilled/purified water
if the tap water in your area is very hard.
Filling Your Steam Shark
With Water
IMPORTANT:
Always insure that the unit is
“UNPLUGGED” from the wall receptacle prior to initial
filling or re-filling the water tank. Failure to follow these
steps will cause the water tank to overfill.
Step 1:
Before filling the Steam Shark, make sure that
the unit is
NOT
plugged in.
Step 2:
Turn Safety/Filler Cap counter clockwise until
removed.
(See caution above.)
Step 3
:
Place Water Filling Funnel in tank and add 780
cc of water
Do not overfill.
Replace Safety/
Filler Cap by turning clockwise. Heating time
is approximately 3-5 minutes with cold water.
Filling boiler with hot water will shorten heat
up time.
Step 4:
Plug the unit into a standard 230volt (3-prong)
grounded wall receptacle. The power light will
illuminate.
Step 5:
Allow approximately 3-5 minutes for vapor to
reach its working temperature and pressure
.
Step 6:
Connect desired attachments onto the Flexible
Steam Hose.
Step 7:
Upon initial use, some water will come out from
the nozzle of the attachment. This is unheated
water in the hose and is normal.
CAUTION: Always drain condensate from hose before
use or if unit has been left idle for a period of time. To
drain hose, direct nozzle into an appropriate container
or sink and depress hand grip steam trigger. Once
hose has been drained, normal use may be resumed.
Never direct nozzle towards people, animals or plants.
IMPORTANT:
When the Steam Shark has run out of water,
steam output will cease.
CAUTION:
Allow unit to cool for 5 minutes before refilling.
When refilling the machine while it is still hot, the first drops
of water might bubble up.
Use caution when opening
the Safety/Filler Cap as cap may become hot during
use and escaping steam can cause scalding.
Refilling Your Steam Shark With Water
Step 1:
Disconnect Electrical Power Cord from wall
outlet.
Step 2:
Depress and hold the hand grip steam trigger
to ensure that any remaining pressure in the
boiler has been released.
Step 3:
Carefully loosen the safety/filler cap by turning
counter clockwise. Any residual steam will be
released below the safety/filler cap if the tank
has not been completely vented. When the
hissing stops and the last of the steam has
been released, remove the filler cap. Allow unit
to cool down.
CAUTION:
Allow unit to cool for 5 minutes before refilling.
If the Steam Shark is still hot, there is a risk that water
will be squirted back during filling and cause scalding.
Extreme care should be taken when refilling the unit.
Use caution when opening the Safety/Filler Cap as
cap may become hot during use and escaping steam
can cause scalding.
Step 4:
Allow the vapor steam cleaner to cool for 5
minutes before re-filling with water.
Step 5:
Refill water tank with water using the filling
funnel.
Step 6:
Firmly screw the safety/filler cap back onto the
unit by turning clockwise.
Step 7:
Connect power cord to the wall outlet.
OPERATING INSTRUCTIONS
Summary of Contents for Steam Shark
Page 1: ...www euroflex it ...
