540mm Upright Cooker with GAS oven User manual
21
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
t
t
h
h
e
e
g
g
a
a
s
s
c
c
o
o
o
o
k
k
e
e
r
r
U
U
n
n
p
p
a
a
c
c
k
k
i
i
n
n
g
g
When packaging is removed from product you will notice there are several items nested in the packaging
base. The burner crowns, burner caps and trivets to be fitted to the hob.
N
N
o
o
t
t
e
e
:
:
T
T
h
h
a
a
t
t
W
W
o
o
k
k
t
t
r
r
i
i
v
v
e
e
t
t
i
i
s
s
a
a
d
d
i
i
f
f
f
f
e
e
r
r
e
e
n
n
t
t
s
s
i
i
z
z
e
e
a
a
n
n
d
d
m
m
u
u
s
s
t
t
b
b
e
e
c
c
o
o
r
r
r
r
e
e
c
c
t
t
l
l
y
y
l
l
o
o
c
c
a
a
t
t
e
e
d
d
o
o
v
v
e
e
r
r
W
W
o
o
k
k
b
b
u
u
r
r
n
n
e
e
r
r
.
.
L
L
o
o
c
c
a
a
t
t
i
i
n
n
g
g
t
t
h
h
e
e
c
c
o
o
o
o
k
k
e
e
r
r
This appliance must be installed by an authorised person in accordance with this instruction manual,
AS/NZS 5601 – Gas installations (installation and pipe sizing), local gas fitting regulations, local electrical
regulations, local water regulations, local health regulations, Building Code of Australia and any other
government authority.
Overhead clearances—(Measurement A) Range
hood
s and exhaust fans shall be installed in accordance
with the manufacturer’s
relevant instructions. However, in no case shall the
clearance between the highest part of the
hob
of the
gas
cooking
appliance
and a
range hood
be less than 600
mm or, for an overhead exhaust fan, 750 mm.
Side clearances—(Measurements B, & C)
Where
B, measured from the periphery of the nearest
burner
to any vertical
combustible surface
, or
vertical
combustible surface
covered with
toughened glass or sheet metal, is less than 200
mm, the surface shall be protected to a height C of
not less than 150 mm above the
hob
for the full
dimension (width or depth) of the cooking surface
area. Where the
gas
cooking
appliance
is fitted with
a ‘splashback’, protection of the rear wall is not
required.
Additional requirements for freestanding and
elevated gas cooking appliances—
(Measurements D & E).
Where D, the distance from
the periphery of the nearest burner to a horizontal
combustible surface is less than 200 mm, then E
shall be 10 mm or more, or the horizontal surface
shall be above the trivet.
G
G
a
a
s
s
t
t
y
y
p
p
e
e
Before installation check that the cooker is suitable for the gas supply. The cookers are manufactured for
both Natural gas or Universal LPG, check the gas type label located on appliance. If the cooker is required
to be converted to a different gas type, a conversion kit can be obtained by contacting the Customer Care
Centre.
Connection to the gas supply
The isolating manual shut-off valve connection point must be installed and accessible when the appliance
is in position. Gas inlet is located at the top rear right hand side, 50mm from the edge. This appliance is
suitable for connection with rigid pipe or flexible hose. For flexible hose connection, the flexible hose