background image

EUROSTER 11K CONTROLLER USER MANUAL

11

GUARANTEE CERTIFICATE

EUROSTER 11K

Warranty terms:

1. Warranty is valid for 24 months from the controller sale date.
2. Claimed controller together with this warranty certificate must be supplied to the seller.

3. Warranty   claims   shall   be   processed   within   14   business   days   from   the   date   the

manufacturer has received the claimed device.

4. Controller may be repaired exclusively by the manufacturer or by other party clearly

authorized by the manufacturer.

5. Warranty becomes invalidated in case of any mechanical damage, incorrect operation 

and/or making any repairs by unauthorized persons.

6. This consumer warranty does not exclude, restrict nor suspend any right of the Buyer 

ensuing if the product would not meet any of the sale contract terms.

…..................................................................................................................................

    sale date

       serial number/date of manufacture 

  signature/stamp 

Business entity that issued this warranty certificate: 
P.H.P.U. AS Agnieszka Szymańska-Kaczyńska, Chumiętki 4, 63-840 Krobia, Poland

Summary of Contents for 11K












Reviews: