background image

9

Your new EVELO bicycle is equipped with a three-inch tire and mounted to a wide rim. Your bike’s 
tire and rim are both designed for maximum comfort, traction, and stability.

This tire and rim combination may be a bit different than bike tires you have used in the past. Given 
the much higher volume created by tire and rim combination, the recommended pressure is sig-
nificantly lower than tire pressure on most bicycles. 

Please reference the table below to correctly set the tire pressure. 

The pressure recommendation printed on the tire should not be used, as they are not suitable for 
this tire and rim combination.

Additionally, it’s always a good idea to check your tire pressure every couple of weeks.  

 

Rider Weight 

Tire Pressure

100-140 Pounds............. 14 PSI
141-160 Pounds..............16 PSI
161-180 Pounds..............17 PSI
181-200 Pounds.............18 PSI
201-220 Pounds.............19 PSI
221-240 Pounds.............20 PSI
241-260 Pounds.............21 PSI
261-280 Pounds.............22 PSI
281-300 Pounds.............23 PSI
301-320 Pounds.............24 PSI
321-340 Pounds.............25 PSI
341 Pounds and Heavier...26 PSI

Summary of Contents for Aurora Limited Edition











Reviews: