3
2
D
C
A
E
To open gate:
• Squeeze the latch
A
upward to unlock;
• Slide the gate in the direction of the arrow to disengage from
the upper latch housing
B
and lower latch housing
C
;
• Swing gate open.
IMPORTANT:
The end of the bottom rail
E
is slightly longer than
the top rail
D
. Before attempting to swing the gate open, make sure
the bottom rail is disengaged.
8.
Swing the gate into the closed position and slide the gate panels until the gate contacts
the latch side of the mounting surface.
9.
Making sure that the top of the gate is level with the floor, using a pencil
E
, carefully
mark the position for the holes for the latch housing
D
.
10.
Swing the gate out of the way, and remove the latch housing.
Installation
11.
Drill holes as in Step 4. Using the correct screws (see Step 5), secure the upper latch
housing to the mounting surface.
12.
Slide the lower latch housing over the lower gate rail.
13.
Using a pencil, carefully mark the position for the holes of the lower latch housing.
14.
Open and swing the gate out of the way. Remove the lower latch housing from the rail.
15.
Drill holes as in Step 4. Using the correct screws (see Step 5), secure the lower latch
housing to the mounting surface.
16.
To close gate, place the lower rail into the lower latch housing, while squeezing the
latch
C
, insert it into the upper latch housing
D
.
17.
Test the gate:
• Check that each slat is securely attached to the top and bottom rails.
• Shake the gate assembly at the top rail to be certain it is securely installed.
•
Wash gate with mild soap and warm water and dry thoroughly before using.
•
Metal and plastic parts can be wiped clean with a soft, damp cloth and dried with a soft cloth.
DO NOT
use abrasive cleaners
or solvents.
•
An occasional drop of vegetable oil may reduce wear and tear on moving parts.
Care and Maintenance
Limited Warranty
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user (“Purchaser”) this
Product (including any accessories) against defects in material or workmanship. Evenflo’s sole obligation under this express
limited warranty shall be, at Evenflo’s option, to repair or replace any Product that is determined to be defective by Evenflo and
determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form of
a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain warranty
service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is not assignable
or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo’s ParentLink Consumer
Resource Center at
(800) 233- 5921
or
www.evenflo.com
.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THIS
PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH
ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.
Gate Operation
#10 x 1/2” Screws
The optional swing control mechanism provides extra security.
We recommend the swing control mechanism be used to prevent
the gate from swinging into a hazard such as over stairs or into a
heavy traffic area.
1.
Mount the gate according to instructions.
2.
Determine the direction you want to prevent the gate from
swinging.
3.
Attach the swing stop
A
to the top rail
B
with the solid
surface of the swing stop toward the direction of the hazard,
i.e. the direction you want to prevent the gate from swinging.
4.
The optional swing control mechanism should not be used in
place of the latching mechanisms. It is not intended to latch or
close the gate.
Always keep the latching mechanism securely engaged when
using the gate. Remove the gate from opening when not in use.
A
B
Optional Swing Control
B
C
D
E
• www.evenflo.com
•
USA:
1-800-233-5921, 8 AM – 5 PM E.T.
•
Canada:
1-937-773-3971 •
México:
01-800-706-12-00
