background image

- 3 - 

 

4 short screws to attach flush-mounting clips 

 

Rubber plug for side hole in outer base. 

 

Mounting template 

 

Power supply pigtail

 

 

Video test cable 

Accessory pack #2 containing two flush mounting clips 

Please Note:

 If an item appears to have been damaged in shipment, replace it properly in its carton 

and  notify  the  shipper.  If  any  items  are  missing,  notify  your  EverFocus  Electronics  Corp.  Sales 
Representative or Customer Service. The shipping carton is the safest container in which the unit may 
be transported. Save it for possible future use. 

1.3 Specifications

   

 

Pickup Device 

1/2.7" 2 megapixel CMOS sensor 

Image area for FOV 1080 mode: 6.61 mm diagonal; 5.76 mm H x 3.24 mm V 

Image area for FOV 720 mode: 4.41 mm diagonal; 3.84 mm H x 2.16 mm V 

Sensitivity 

0.5lux/F=1.4 ; 0 lux IR ON 

S/N Ratio 

45dB 

Video Format Main Output 

HDcctv 

Resolution Main Output 

1920x1080 or 1280x720 

Video Mode Main Output 

Field select 1080i60, 1080p30 or 720p60 for 60Hz systems 

1080i50, 1080p25 or 720p50 for 50Hz systems 

Main Output Connector 

BNC-F 

Video Format Test Output 

NTSC/PAL selectable 1V p-p 

Test Output Connector 

Pin header; adapter cable to BNC-F supplied 

Electronic Shutter 

Auto, 1/60(1/50)~1/8000 

Lens Type 

Megapixel Vari-focal lens, Auto Iris, f=3.3~12mm, F=1.4 

True Day/Night Control 

Yes (Auto IR cut filter removal) 

Back Light Compensation 

On/Off selectable 

Auto Gain Control 

High/Middle/Low/Off selectable 

Auto White Balance 

AWB/One Push WB/Manual WB/Indoor/Outdoor selectable 

Gamma Correction 

PC/TV selectable 

OSD Menu 

Yes (operated from 5-axis joystick control) 

Mirror 

H_MIR/V_MIR

/

Rotate 

IR Distance 

20m/65 feet 

IR Wavelength 

850nm 

IR Emitters 

34 high output LEDs 

IR LED Lifespan 

20,000 hours operating 

Power Source 

12VDC/24VAC auto polarity detect 

Power Consumption 

24VAC: 7.2W IR off, 11.3W max (300mA/471mA)   

12VDC: 4.7W IR off, 7.4W max. (392mA/617mA) 

Dimensions (

ϕ x H

Surface Type: 140mm x 128mm / 5.5” x 5.1” 

Flush Type : 140mm x 68mm / 5.5” x 2.8” 

Weight 

660kg /1.45 lbs 

Operating Temperature 

0°C~40°C ; 32°F~104°F (20%~80% Humidity) 

All manuals and user guides at all-guides.com

Summary of Contents for EDH5240
























Reviews: