background image

                                           

 

 

 

 

Safety Notice

 

Federal Communication Commission Interference Statement 

This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one of the following measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver  is 

connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 

FCC Caution:

 Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to operate this equipment. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation. 
 

 

 

 

Summary of Contents for EMW990F











Reviews: