background image

 

EVERFOCUS

 

 

  Indoor Pendent Dome Camera 

Operation Instructions

 
 
 

Model No. 

EPD200

 

 
 
 
 
 

Please read this manual first for correct installation and operation. This manual should be retained 
for future reference. The information in this manual was current when published. The 
manufacturer reserves the right to revise and improve its products. All specifications are therefore 
subject to change without notice.   

 

PRECAUTIONS 

1. 

Do not install the camera near electric or magnetic fields.   

Install the camera away from TV, radio transmitter, magnet, electric motor, transformer, 
audio speakers since the magnetic fields generate from above devices will distort the video 
images. 
 

2. 

Never disassemble the camera nor put impurities in it. 

Disassembly or impurities may result in trouble or fire. 
 

3. 

Never face the camera toward the sun. 

Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit. 
 

4. 

Keep the power cord away from water and liquid. 

Touching the wet power cord may result in electric shock. 
 

5. 

Never install the camera in areas exposed to water, oil or gas. 

Water, oil or gas may result in failure, electric shock or fire. 
 

Summary of Contents for Indoor Pendent Dome Camera EPD200











Reviews: