background image

CHAPTER 1 

Operation and Care Manual

 

The  operation  and  care  manual  is  a  document 

issued by the manufacturing company and is an 

integral  part  of the  machine.  This document  is 

adequately  identified  for  easy  tracing  and/or 

subsequent references. 

All  rights  relating  to  the  reproduction  and 

disclosure  of  the  information  contained  in  this 

handbook and the documentation quoted and/or 
attached  are  reserved.  This  handbook  contains 

the information necessary for the customer and 

assigned  personnel,  to  ensure  the  correct 

installation,  use  and  maintenance  of  the 

appliance allowing it to be used safely. 

Safety precautions and  

Manufacturer’s

 liabilities. 

Every operations related to the intended use of 

this appliance and its overall life cycle has been 

carefully  and  thoroughly  analysed  by  the 
manufacturing  company  during  the  design 

phase, construction phase and the writing of the 

operation and care manual. 

It  is  nevertheless  understood  that  experience, 

proper 

training  and  “common  sense”  of  the 

personnel  operating  this  appliance  are  of  the 

utmost importance. It is the responsibility of the 

operator  to  observe  all  safety  precautions  as 

outlined  in  this  manual  and  to  operate  this 

appliance accordingly.  

The non-observance of the safety precautions or 

specific  warnings  indicated  in  this  manual,  the 

use of this appliance by unauthorized personnel, 
violation  of  all  safety  standards  regarding  the 

design,  construction,  and  intended  use  of  the 

machine,  will  relieve the  manufacturer from  all 

liability  in  the  case  of  damage  to  personnel  or 

property. 

The  manufacturing  company  is  therefore  in  no 

way responsible for the non-observance on the 

part of the user of the safety precautions listed 

in this manual. 

Regulatory references 

The following manual 

CONFORMS TO

ANSI/UL Std. 963 

 CERT. TO CAN/CSA 

Std.C22.2 No. 68 

 CONFORMS TO NSF 169

Disposal of this appliance after its 

useful life.

 

Electric  and  electronic  appliances  contain 

dangerous substances that may have potentially 

harmful effects for people and the environment. 

It is recommended to dispose of it properly, 

DO 

NOT  DISPOSE  OF  ELECTRICAL  OR 

ELECTRONIC  EQUIPMENT  WITH  OTHER 

MUNICIPAL WASTE. 

CHAPTER 2 

How  to  use  the  Operation  and 

Care Manual 

This document is an integral part of the machine. 

Preserve a copy of this operation manual for the 

entire  working  life  of  the  appliance  even  if 

transferred  or  sold.  Additional  copies  can  be 

obtained from the manufacturer.  

To  maintain  the  operation  and  care  manual  in 

good condition: 

1. Use the operation and care manual carefully

so  as  to  not  to  damage  its  contents.  In

particular,  do  not  leave  the  operation  and

care manual around after use and return it to

its 

proper 

place 

immediately 

after

consultation.

2.

Do not remove, rip out or rewrite parts of the

operation and care manual. Any changes to

this  manual  are  to  be  issued  by  the

manufacturer.

3. Keep the operation and care manual in a safe

place,  away  from  environmental  elements

which could damage it.

Summary of Contents for PrepRite PVS27-6-1



























Reviews: