background image

CHAPTER 3 

WARRANTY 

PrepRite

  Inc.  warrants  to  the  original

purchaser only that any original part that is 
found  to  be  defective  in  material  or 
workmanship will,  at 

ThermalRite’s

 option, 

subject to provisions hereinafter stated, be 
replaced with a new or rebuilt part. For all 
other original parts, twelve (12) months from 
the date of shipment of appliance. The labor 
warranty period is twelve (12) months from 
the  shipping  date. 

PrepRite

  will  bear

normal  labor  charges  performed  during 
standard business hours, excluding 
overtime, holiday rates or any additional 
fees. To be valid, a warranty claim must be 
filed during the applicable warranty period. 
This warranty is not transferable. 

1. All  machine  components  normally

subject  to  wear  and  are  considered
consumables are not included in the
warranty: Teflon sealing bars, rubber

gaskets  ,  chamber  opening  pistons,
sealing gaskets ,air filters , oil filters ,
oil changes, pump blades.

2. If the vacuum pump of an appliance

is replaced under warranty because of
aspiration 

problems, 

the

manufacturer has the right to inspect

whether  any  foreign  bodies  have
been  aspirated  (liquids,  solids,
sauces, etc.). If this is the case, the

repair  (part  and  labor)  will  not  be
covered, since the problem is not due
to  manufacturing  defects,  but  to
customer negligence during use.

3.

Possible conditions causing electronic
controls  to  fail  include  incorrect
electrical 

supply, 

environmental

elements,  storms,  lightning,  water
damage, could cause damages which
cannot  be  attributed  to  the

manufacturing  company  and  to  the
manufacture of the product itself.

4. During  the  warranty  period,  for  any

defect in workmanship and material,

all parts and labor will be covered. All
warranty claims must be submitted to

and  conform  by  all  statements  and 
policies  of  the  OneSolutionSupport 
service.  

5. During  the  warranty  period,  we  will

pay,  not  to  exceed,  one  (1)  hour
travel  and  fifty  (50)  miles  travel.  All

warranty service will be performed by
an authorized service center certified
by  the  manufacturer.  All  parts

replaced  under  warranty  must  be
returned  to  the  manufacturer  for
inspection  before  any  warranty  is
paid.

6. Any components considered defective

(pump, electronic control, etc.) and is
determined to be caused by misuse or

abuse 

during the warranty period

will  not  be  considered  under
warranty.  The  end  user  will  be
responsible for any repairs or parts for

repairs.

7. Equipment  modified  in  any  manner

from  original  model,  substitution  of

parts  other  than  factory  authorized
parts, removal of any parts including
legs, or addition of any parts.

8. Any losses or damage resulting from

malfunction, including loss of product,
food 

product, 

revenue, 

or

consequential  or  incidental  damages

of any kind.

9. Equipment

damage  caused  by 

accident, 

shipping, 

improper 

installation or alteration. 

10.

 

This  warranty  is  exclusive  and  is  in
lieu of all other warranties, express or

 

implied, including the implied

 

warranties of  merchantability and

 

fitness for a particular purpose.  In no

 

event  shall 

PrepRite

  be  liable  for

 

loss of use, loss of revenue or profit,

 

or loss of product, or for any indirect,

 

special,  incidental,  or  consequential

 

damages. No person except an officer

 

of 

PrepRite

  Inc.  is  authorized  to

 

modify  this  warranty  or  to  incur  on

 

behalf  of 

PrepRite

  any

other

 

obligation  or  liability  in  connection

 

with 

PrepRite

 equipment.

Summary of Contents for PrepRite PVS27-6-1



























Reviews: