CUSTOMER SERVICE 1-888-707-1880 Dyaco Canada Inc.©2014
10
1
#102
. 5/16” × 2-1/4”
Hex Head Bolt (4 pcs)
#103
. 3/8” × 3/4”
Hex Head Bolt (2 pcs)
#104
. 3/8” × 1-1/2”
Hex Head Bolt (2 pcs)
#105
. 3/8” × 2-1/4”
Hex Head Bolt (1 pc)
#116
. M5 × 10mm
Phillips Head Screw
(4 pcs)
#130
. 3/8” × 7T
Nyloc Nut (2 pcs)
#137
. 3/8” × 19 × 1.5T
Flat Washer (2 pcs)
#142
. 5/16” × 20 × 1.5T
Flat Washer (4 pcs)
#151
. 5/16” × 1.5T
Split Washer (4 pcs)
#152
. 3/8” × 2T
Split Washer (1 pc)
#153
. 3/8” × 23 × 2T
Curved Washer (2 pcs)
#154
. 5/16”
Star Washer (4 pcs)
Assembly Instructions
Rear Rail, Console Mast & Console
1. Slide the Incline Rail Assembly (
2
) into the U channel of the Main
Frame (
1
). Be very careful not to damage the wires that exit each
part.
2. Connect the Incline Rail Assembly (
2
) horizontally to the U channel
of the Main Frame (
1
) with two Hex Head Bolts (
104
), two Flat
Washers (
137
) and two Nyloc Nuts (
130
). Secure it vertically with
four Hex Head Bolts (
102
), four Split Washers (
151
), four Flat
Washers (
142
) and four Star Washers (
154
). Tighten using the
Wrenches provided (
155
&
158
).
3. Connect the Incline Motor wires (
49
&
50
) to the wiring harness that
exits the Incline Rail Assembly (
2
), by matching the colors red, white
and black. Push the excess cable inside the U channel. Guide the
twist tie that is attached to the Computer Cable (
44
) through the
bottom of the Console Mast (
12
) until it exits the top of the steel tube.
Secure the Console Mast (
12
) by loosely threading two Hex Head
Bolts (
103
) from the front and two Curved Washers (
153
) first. Then
secure the mast from the side by loosely threading a Hex Head Bolt
(
105
) and a Split Washer (
152
).
Note
:
There is one bolt already
installed in the receiving bracket that will engage with the slot at the
bottom of the Console Mast. Tighten the two bolts from the left side
last.
4. Tighten the two front bolts first, then the side bolts with the Wrench
(
155
).
5. Untie the twist tie from around the Computer Cable (
44
). Plug the
Computer cable (
44
- wide white end) & the two Hand Pulse Cables
(
47
) into the bottom of the Console (
43
). Insert the Resistance Cable
(
165
) into the white port labeled “Load” and the Incline Cable (
166
)
into the Incline port on the back of the Console. Secure the Console
(
43
) onto the mounting plate with four Phillips Head Screws (
116
).
Tighten them with the Phillips Head Screw Driver (
157
).
6. Install the water bottle holder onto the handlebar in any position you
like.
Hardware Step 1
