Model 5601MSC
Model 5601MSC Master SPG/Master Clock System
Page - 170
Revision 2.2
TECHNICAL DESCRIPTION
5.1.11. 3GTV Test Generator Outputs (3GTG option installed)
SDI Standards:
SMPTE ST 259-C (270Mb/s) 4:2:2 10 Bit YCbCr
SMPTE ST 292-1 (1.485 Gb/s) 4:2:2 10 Bit YCbCr
SMPTE ST 372 (Dual Link 1.485 Gb/s) 4:2:2 10 Bit YCbCr and 4:4:4
GBRA or YCbCr
SMPTE ST 292-2 (Stereoscopic 3D Dual Link 1.485 Gb/s) 4:2:2 10 Bit
YCbCr
SMPTE ST 425-1 Level A 4:2:2 10 Bit YCbCr, SMPTE ST 425-1 Level B-
DL 4:2:2 10 Bit YCbCr and 4:4:4 GBRA or YCbCr
SMPTE ST 425-2 (Stereoscopic 3D 2.97 Gb/s) 4:2:2 10 Bit YCbCr
SMPTE ST 424 (2.907 Gb/s)
Image Standards:
SMPTE ST 125 (525 line and 625 line 13.5 MHz sampling)
SMPTE ST 274 (1080i/59.94, 1080i/60, 1080i/50, 1080p/30, 1080p/25,
1080p/29.97, 1080p/23.98, 1080p/23.98sF, 1080p/24, 1080p/24sF,
1080p/50, 1080p/59.94, 1080p/60)
SMPTE ST 296 (720p/24, 720p/30, 720p/50, 720p/59.94, 720p/60)
SMPTE ST 2048-2 (2048x1080p/23.98, 2048x1080p/24, 2048x1080p/25,
2048x1080p/29.97, 2048x1080p/30, 2048x1080p/47.98, 2048x1080p/48,
2048x1080p/50, 2048x1080p/59.94, 2048x1080p/60)
Number of Outputs:
4:2:2
4 individual test generators with 2 outputs each
4:4:4
In dual-link mode each TG has one output Link A, other output Link B
In 3G mode each TG has 2 identical outputs
Embedded Audio:
Up to 4 groups of audio as specified in SMPTE ST 299-1.
Selectable tone frequencies (from 20Hz to 20kHz) and audio level control
Connector:
BNC per IEC 61169-8 Annex A
Signal Level:
800mV ± 10% nominal, 1600mV high drive
Rise and Fall Time:
400ps to 800ps (270 Mb/s),
< 270ps (1.485 Gb/s)
< 135ps (2.97 Gb/s)
Rise and Fall Overshoot:
< 10% of amplitude
Return Loss:
> 15dB to 1.5GHz
> 10dB to 3.0GHz
Alignment Jitter:
< 0.3 UI (100kHz high-pass filter)
Timing Jitter:
< 2.0 UI (10Hz high-pass filter)
5.1.12. General Purpose Inputs and Outputs
Number of Inputs:
2 (can send SNMP trap on activation)
Number of Outputs:
2 (function menu selectable)
Type:
Opto-isolated, active low with internal pull-ups to +5V
Connector:
4 pins plus 2 ground pins on GPIO connector (female DB15)
Signal Level:
+5V maximum