background image

570J2K-HW-X19 

Multi channel J2K Encoder-Decoder

 

 

 

Revision 1.0

 

Page - 17

 

5.3. 

SDI INPUT CONTROL 

 

Figure 

 

5-7 : WebEASY

® 

- SDI Input Control Tab 

5.3.1.  Input Status 

Input Select:

 

This parameter configures the Max Link Rate for the specified channel path.  It is used only when 

the channel paths are set for Encapsulation.  The user can select the following modes SDI-SD, SDI-HD, 3G-SDI.  
When configured to SD the max encapsulation on the link can handle up to 270Mbps.  If a HD input is provided, 
the signal will be clipped.  If the Input select is configured to HD, the max encapsulation on the link can handle up 
to 1.5Gbps.  If a 3G input is provided the signal will be clipped.  When the input select is configured to 3G, the 
max encapsulation on the link can handle up to 3Gbps.  

Video Standard Detected:

 This parameter displays the current video standard which is detected. 

SDI Loss Count:

 This parameter displays the SDI loss counter. 

Input Alias:

 This parameter displays the input alias. 

Clear SDI Loss Count:

 This button allows the user to clear the SDI loss counter. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 570J2K-HW-X19





























































Reviews: