- 54 -
Eseguite le regolazioni in altezza de-
scritte al par. 5.2, verificare il corretto
livello di tutti gli olii ed eseguire l’in-
grassaggio in ogni punto previsto.
Prima di utilizzare la macchina, fa-
miliarizzare con essa, in particolare
verificare le corrette manovre per
arrestare velocemente le operazioni
di lavoro.
- Abbassare il sollevatore fino a che
le lame siano vicine al terreno senza
toccarlo.
- Inserire la presa di forza.
- Abbassare completamente il solle-
vatore del trattore.
IMPORTANTE
Non far cadere con violenza la
macchina sul terreno, ma scen-
dere lentamente per consentire il
graduale inserimento delle lame
nel terreno.
In caso contrario si provochereb-
bero forti sollecitazioni su tutti i
componenti della macchina che
potrebbero compromettere seria-
mente la loro integrità.
Durante il lavoro il sollevatore
deve essere sempre completa-
mente abbassato e con i dispo-
sitivi di controllo della posizione
e dello sforzo disinseriti in modo
da non influenzare la profondità
di lavoro della macchina che va
regolata solo mediante i dispo-
sitivi (rullo, ecc...) presenti sulla
macchina stessa.
IMPORTANT
Do not allow the machine to drop
violently on to the ground.
Lower it slowly to allow the knives
to gradually cut into the soil.
Violently impact would strongly
stress all machine components
and could cause serious dam-
ages.
During work, the lift must always
be fully lowered with the draft
control and position devices dis-
engaged so that they are unable
to influence the work depth of the
machine.
This should only be regulated by
means of the devices (roller, etc.)
on the machine itself.
Make the height adjustments de-
scribed in paragraph 5.2. Check that
all oil supplies are at the correct level
and grease all required points.
Always become familiar with machine
use before working with the imple-
ment.
Make sure that you know how to quickly
stop the work operations.
- Lower the lift until the knives are near
the ground without touching it.
- Engage the pto.
- Completely lower the tractor lift.
Summary of Contents for HARDEE HT3
