background image

 

24 

 

2551988C 

 

WARRANTY 

The warranty has value if good practice has been strictly observed during installation and in use. 
Evinox Energy is not liable for equipment breakdown and damage to persons and objects caused by:

 

 

Transportation damage

 

 

Installation in which the instructions and good practice were not complied with

 

 

Improper use of the device, abnormal use conditions, tampering by unauthorised personnel or 
inadequate maintenance; corrosion and/or sludge accumulation; lack of electrical energy; 
absence of suitable drainage; exceeding operating limits, electrical and water system faults

 

 

Frost damage

 

 

Wear due to normal use

 

 

Malfunctioning of system controls and or safety systems

 

 

Corrosion due to oxygenation poor water quality or roaming currents

  

 

The pump being run against a closed system. 
 

From commissioning, ModuSat appliances have a warranty against all manufacturing faults and 
material defects for a period of:

 

 

5 years for the stainless steel plate heat exchangers

 

 

2 years for parts and labour Note: w

here Evinox Energy do not carry out the commissioning the 

two-year warranty will cover parts only with no labour cover)

 

 

The ModuSat warranty will always start from the commissioning date providing this date is within six 
months of the date of invoice to allow for project completion. If the ModuSat is commissioned 
outside the 6-month extension date, the warranty will reduce accordingly.

 

This warranty is strictly limited to the supply, free of charge, of parts acknowledged as being 
defective after inspection by our technical department. Any costs arising from this inspection will be 
charged if the part is deemed not to be defective. The defective parts must be returned otherwise 
the replacement part will be charged for.

 

Failure to comply with the relevant installation requirements of the Building Regulations, Local 
Water Byelaws and Building Standards will invalidate any warranty claim.

 

The ModuSat must be fitted with the ModuSat Flushing by-pass isolation valve kit for ease of 
servicing and undertaking warranty work. Warranty calls that include draining the system will be 
chargeable if isolation valves have not been fitted. 

 

It is imperative that the level of corrosion protector within the system is kept within industry 
guidelines at all times. Special attention should be given to ensure that, after any decoration or 
building works where radiators might be removed, the system is replenished with chemicals. Non-
use of inhibitor will invalidate the warranty.

 

We will record details of the unit and commence the warranty when we commission the ModuSat 
units.

 

Any warranty claims that are a result of user error, poor installation or lack of servicing will be 
chargeable. Please note that all replacement parts provided under warranty are subject to factory 
inspection to determine cause of failure. Replacement parts are chargeable until passed as faulty by 
Evinox Energy, when a credit will be provided. Any parts that have failed as a result of poor servicing 
or misuse will not be covered by our warranty.

 

Summary of Contents for ModuSat SP Cooling Unit

































Reviews: