background image

GUARANTEE

This product is guaranteed against defects in material and workmanship for 2 years 
from the date of purchase, under normal usage. The guarantee DOES NOT APPLY 
in case of improper use, negligence, lack of maintenance or accidental damage to 
the evoUV. If the evoUV fails due to a manufacturing fault within this period it will 
be either repaired or replaced free of charge. Liability is limited to replacement of 
the faulty product only; no other costs will be reimbursed. This guarantee is not 
transferable and does not affect your statutory rights. This guarantee does not confer 
any rights other than those expressly set out above. This guarantee does not cover 
the evoUV bulb or quartz sleeve.

The manufacturer or supplier shall not be responsible, or held liable for any 
damages caused by defective components or materials of this product; or for loss 
incurred by interruption of service; or any consequential/incidental damages and 
expenses arising from the production, sale use or misuse of this product or any other 
consequential loss.

IMPORTANT: 

Please keep your proof of purchase (sales receipt) safe for the 

duration of the warranty period, as this will be needed in the event of a  
warranty claim.

Evolution Aqua and its dealers shall not be held liable for any loss of fish, plants or 
any other livestock as a result of any failure or defect of this product. 

The installation and use of your product outside of our recommendations as printed 
in this manual may also void the warranty.

18

Summary of Contents for evoUV





















Reviews: