MILJÖSKYDD
Återvinn de material du inte behöver istället för att slänga dem
i soporna. Alla verktyg, slangar och förpackningsmaterial
bör sorteras och lämnas på din lokala återvinningsstation
och kasseras på sådant sätt som är säkert för miljön.
Undersökningslista för återvinningsbara material
Material
Vikt (Kg)
Procent ( % )
Aluminum
Gjutjärn
Järnplåt
Plast
Övriga
Totalt
1.94
0.0
3.61
1.96
0.10
7.61
25.40%
0.00%
47.00%
25.70%
1.30%
Pakkausmateriaalit
Material
Vikt (Kg)
Kartong
Polystyren
Polyetylen med låg densitet
Polypropylen
Övriga
Totalt
1.23
0.0
4.50
0.001
0.0
5.731
intended as a guide only and should not be relied upon for the accuracy
of a cut. Remove the battery compartment cover and fit the supplied
batteries, taking care to observe the correct polarity, then replace the
cover. Press the switch to the on position to activate, and remember to
turn off the laser when you have finished a cut. Before use the sight must
be aligned by means of the adjustment screw.
Important Notice: Do
not point the laser at anyone and NEVER look into the laser light, as
serious eye damage may occur
.
Chip Collection
This tool is provided with a chip collector compartment. When the chips
accumulate up to the see-through window, remove the cover, clean out
the cover, then replace it, and tighten the knobs.
Notice
: The metal chips
inside the cover may be very hot and sharp - do not touch with bare
hands.
Maintenance And Troubleshooting
Keep tool, cord, and carry case clean and
free from chips
. Avoid using
cleaning products, which include benzene, trichloroethelene, chloride,
or ammonia as these can damage plastic parts. In case of electrical or
mechanical malfunction, immediately switch off the tool and disconnect
the plug. Excessive sparking may indicate the presence of dirt in the
motor or worn out carbon brushes. Check for wear and replace when
they reach 1/4” (6mm). For all other service take machine to your local
dealer, or to Evolution Power Tools USA, Iowa, if bought in the USA.
Lubrication
Your machine gearbox is lubricated at the factory. To check and / or add
lubricant, it is necessary to dismantle the tool. This operation should
always be handled by the nearest SERVICE CENTER or Evolution
Power Tools USA, Iowa, if in the USA. All repairs and servicing made
by these centers are fully guaranteed against defective materials and
workmanship.
Accessories – Genuine Evolution Blades
40T
9” (230mm) TCT Wood Blade
48T
9” (230mm) TCT Mild Steel Blade
60T
9” (230mm) TCT Stainless Steel Capable Blade
80T
9” (230mm) TCT Aluminium Blade
Notice: Fair wear and tear and damage caused by misuse is not
covered under the 12-Month guarantee.
Gebruiksaanwijzing
Belangrijk
De gebruiksaanwijzing en veiligheidsvoorschriften aandachtig
doorlezen. Het voltage verifiëren en controleren of alle handgrepen
en onderdelen stevig vastzitten met het oog op uw veiligheid. Neem
contact op met uw distributeur in geval van twijfel.
De gebruiksaanwijzing op een veilige plaats bewaren
Specificaties voor het EVO230-HDX model
Motor (230V of 115V 50/60 Hz) (Watt):
1750
Maximale zaagdiepte (6mm dikte 90
0
) (mm):
84
Maximale zaagdiepte (6mm dikte 45
0
) (mm):
53
Maximale Zaagdikte (Plaat in zacht staal) (mm):
12
RPM onbelast (min-1):
2700
Aanbevolen maximale werkduur (minuten):
30
Geluidsdrukniveau (belast) (dB(A)):
108.7
Trillingsniveau (belast) (m/s
2
):
3.9
Gewicht (Kg):
9.0
30
5
