manualshive.com logo in svg

Exar XRT86VL38, Manual

The Exar XRT86VL38 user manual is available for free download on 88.208.23.73:8080. This comprehensive manual provides detailed instructions, troubleshooting tips, and useful insights for maximizing the potential of your XRT86VL38. Accessible in a few clicks, this manual will assist you in harnessing the full power of your XRT86VL38.

Share
Download
background image

XRT86VL38

PRELIMINARY

xr

OCTAL T1/E1/J1 FRAMER/LIU COMBO

REV. P1.0.6 

19

TxCHN0_0/

TxSIG0

TxCHN1_0/

TxSIG1

TxCHN2_0/

TxSIG2

TxCHN3_0/

TxSIG3

TxCHN4_0/

TxSIG4

TxCHN5_0/

TxSIG5

TxCHN6_0/

TxSIG6

TxCHN7_0/

TxSIG7

D12

C18

F22

L22

AD21

AC15

AB10

AC5

B11

C16

C21

K19

W16

AB13

W11

W4

I/O

Transmit Time Slot Octet Identifier Output-Bit 0 / Transmit Serial Sig-
naling Input:

The exact function of these pins depends on whether or not the 
XRT86VL38 is configured to use the transmit fractional/signaling interface. 
The two different functions are described below:  

If transmit fractional/signaling interface is not used - Transmit Time Slot 
Octet Identifier Output-Bit 0

If the transmit  fractional/signaling interface is disabled, these output sig-
nals (TxCHNn_4 through TxCHNn_0) reflect the five-bit binary value of the 
number of the current time slot being accepted and processed by the 
transmit payload data input Interface block.  Terminal Equipment can use 
the TxCHCLK to sample the five output pins of each channel in order to 
identify the time slot being processed. This pin indicates the Least Signifi-
cant Bit (LSB) of the time slot channel being processed.

If transmit fractional/signaling interface is used - Transmit Serial Signaling 
Bus Input

If the transmit fractional/signaling interface is enabled, these pins can be 
used to input robbed-bit signaling data within an outbound DS1 frame or to 
input Channel Associated Signaling (CAS) bits within an outbound E1 
frame, as described below. 

T1 Mode:

In T1 mode, signaling data (A,B,C,D) of each channel needs to be pro-
vided on bit 4,5,6,7 of each time slot on the TxSIG pin if 16-code signaling 
is used. If 4-code signaling is selected, signaling data (A,B) of each chan-
nel must be provided on bit 4, 5 of each time slot on the TxSIG pin.  If 2-
code signaling is selected, signaling data (A) of each channel must be pro-
vided on bit 4 of each time slot on the TxSIG pin.

E1 Mode:

In E1 mode, the signaling data format inserted on the TxSIGn pins will be 
different depending on the TxSIGDL bits setting (from register 0xn10A).  If 
TxSIGDL = 001 or 011, signaling data format inserted on the TxSIGn pins 
will be just like T1 mode.  Signaling data (A,B,C,D) of each channel needs 
to be provided on bit 4,5,6,7 of each time slot on the TxSIG pin if 16-code 
signaling is used. If 4-code signaling is selected, signaling data (A,B) of 
each channel must be provided on bit 4, 5 of each time slot on the TxSIG 
pin.  If 2-code signaling is selected, signaling data (A) of each channel 
must be provided on bit 4 of each time slot on the TxSIG pin.

If TxSIGDL = 010, signaling data (A,B,C,D) of channel 1 and channel 17 
must be inserted on the TxSIGn pin during time slot 16 of frame 1, signal-
ing data (A,B,C,D) of channel 2 and channel 18 must be inserted on the 
TxSIGn pin during time slot 16 of frame 2...etc.  The CAS multiframe Align-
ments bits (0000 bits) and the extra bits/alarm bit (xyxx) must be inserted 
on the TxSIGn pin during time slot 16 of frame 0. 

N

OTES

: 

1.

Transmit fractional interface can be enabled by programming to 
bit 4 - TxFr1544/TxFr2048 bit from register 0xn120 to ‘1’.

2.

These 8 pins are internally pulled “Low” for each channel.

TRANSMIT SERIAL DATA INPUT

S

IGNAL

 N

AME

420 P

KG

B

ALL

#

484 P

KG

B

ALL

 #

T

YPE

D

ESCRIPTION

Summary of Contents for XRT86VL38



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XRT86VL38

Hawking H-GA32T Specifications preview
H-GA32T
Brand: Hawking Pages: 2
National Instruments NI 6731 Calibration Procedure preview
NI 6731
Brand: National Instruments Pages: 13
Access security product RD-SR2 User Manual preview
RD-SR2
Brand: Access security product Pages: 10
ICS Advent ADIO1600 Series Product Manual preview
ADIO1600 Series
Brand: ICS Advent Pages: 72
Digitus DA-70824 Quick Installation Manual preview
DA-70824
Brand: Digitus Pages: 4
DKS 1520 series Manual preview
1520 series
Brand: DKS Pages: 2
Gainward 210 512MB DDR2 Brochure preview
210 512MB DDR2
Brand: Gainward Pages: 2
ATI Technologies X850 - Radeon Xt Platinum Edition 256 Mb Agp User Manual preview
X850 - Radeon Xt Platinum Edition 256 Mb Agp
Brand: ATI Technologies Pages: 90
IFM Electronic DTE800 Operating Instructions Manual preview
DTE800
Brand: IFM Electronic Pages: 37
Delkin Devices 15 User Manual preview
15
Brand: Delkin Devices Pages: 11
AUDIOLINE UDR600 User Manual preview
UDR600
Brand: AUDIOLINE Pages: 2
Contec DIO-1616T-LPE User Manual preview
DIO-1616T-LPE
Brand: Contec Pages: 55
ClearClick HD Capture Box 1080p Users Manual & Quick Start Manual preview
HD Capture Box 1080p
Brand: ClearClick Pages: 10
Audinate Dante-MY16-AUD User Manual preview
Dante-MY16-AUD
Brand: Audinate Pages: 46
ADLINK Technology cBP-3210PR Quick Reference Manual preview
cBP-3210PR
Brand: ADLINK Technology Pages: 17
Videofied BR250 Installation Sheet preview
BR250
Brand: Videofied Pages: 4
Rosslare DR-12C User Manual preview
DR-12C
Brand: Rosslare Pages: 2
Rosslare AY-x25B Series Installation Manual preview
AY-x25B Series
Brand: Rosslare Pages: 3

Brands by name

Popular brands

Load more brands