background image

Table Of Contents

Installation Considerations ��������������������������������������������������������������������������������������� 3

6 Pin Main Wire Harness �������������������������������������������������������������������������������������������� 3

Red & Red/White Wires - Constant Power (+) Input ������������������������������������������������ 3

Pink Wire - Ignition #1 (+) Input/Output �������������������������������������������������������������������� 3

Orange Wire - Accessory (+) Output ������������������������������������������������������������������������ 4

Violet Wire - Start (+) Output ������������������������������������������������������������������������������������ 4

Pink/White Wire - Ignition #2 (+) Output - Programmable ���������������������������������������� 4

18 Pin Secondary Wire Harness �������������������������������������������������������������������������������� 4

Black Wire - System Ground (-) Input ���������������������������������������������������������������������� 4

Orange Wire - Starter Interrupt (-) Output & Relay ��������������������������������������������������� 4

Brown/Red Wire - Brake Pedal (+) Input ������������������������������������������������������������������ 4

Black/White Wire - Neutral Safety (-) Input �������������������������������������������������������������� 4

Violet/White Wire - Tach Signal Input ����������������������������������������������������������������������� 5

Brown Wire - Siren (+) Output ���������������������������������������������������������������������������������� 5

White Wire - Flashing Light (+) Output ��������������������������������������������������������������������� 5

White/Black Wire - Flashing Light (-) Output ������������������������������������������������������������ 5

Gray Wire - Hood Trigger (-) Input ���������������������������������������������������������������������������� 5

Green Wire - Door Trigger (-) Input �������������������������������������������������������������������������� 5

Violet Wire - Door Trigger (+) Input �������������������������������������������������������������������������� 5

Red/White Wire - Trunk Release / 2nd Channel (-) Output �������������������������������������� 6

Black/Red Wire - Light Relay N/O (+/-) Input ����������������������������������������������������������� 6

Green/Violet Wire - Light Relay COM Output ����������������������������������������������������������� 6

White/Red Wire - Light Relay N/C Input ������������������������������������������������������������������� 6

Violet/Black Wire - Horn Relay N/O (+/-) Input ��������������������������������������������������������� 6

Blue/Black Wire - Horn Relay COM Output �������������������������������������������������������������� 6

Brown/Black Wire - Horn Relay N/C Input ���������������������������������������������������������������� 6

6 Pin Secondary Wire Harness ���������������������������������������������������������������������������������� 7

Pink Wire - 3rd Channel (-) Output ��������������������������������������������������������������������������� 7

White/Blue Wire - Remote Start Activation (-) Input ������������������������������������������������� 7

White Wire - Alarm Arm (-) Input ������������������������������������������������������������������������������ 7

Brown Wire - Alarm Disarm (-) Input ������������������������������������������������������������������������ 7

Lt� Green/Red Wire - OEM Alarm Arm / CH4 (-) Output ������������������������������������������� 7

Lt� Green/Black Wire - OEM Alarm Disarm / CH5 (-) Output ������������������������������������ 7

3 Pin Satellite Relay Port (RED) �������������������������������������������������������������������������������� 7

Wiring Overview Diagram ������������������������������������������������������������������������������������������ 9

3 Pin Satellite Relay Port (BLUE) ���������������������������������������������������������������������������� 10

4 Pin Door Lock/Unlock Port (RED) ������������������������������������������������������������������������ 10

2 Pin Backup Battery Port (WHITE) ������������������������������������������������������������������������ 10

Green Data Port ���������������������������������������������������������������������������������������������������������11

Black Data/Programming Port����������������������������������������������������������������������������������11

BLADE Cartridge Port �����������������������������������������������������������������������������������������������11

Dual Zone Sensor Ports (WHITE) �����������������������������������������������������������������������������11

Window Mount Antenna Module ����������������������������������������������������������������������������� 12

Status Lights ������������������������������������������������������������������������������������������������������������� 12

Valet / Programming Switch ������������������������������������������������������������������������������������ 12

Tach Programming ��������������������������������������������������������������������������������������������������� 12

Programming Transmitters�������������������������������������������������������������������������������������� 13

Programmable Features ������������������������������������������������������������������������������������������ 15

Summary of Contents for AL-XX50-EDPB

















Reviews: