background image

15

Programmable Features Matrix

This device complies with FCC Rules part 15. Operation is subject to the following two condi-
tions, (1) This device may not cause harmful interference and, (2) This device must accept 
any interference that may be received, including interference that may cause undesired 
operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized 

modifications to this equipment. Such modifications could void the user’s authority to operate 

the equipment.

Feature #12   Data Port Protocol

D2D (Trilogix)

  (press “

lock

” button to program) 

- DEFAULT

ADS (iData) 

(press “

unlock

” button to program)

 

This feature determines which data protocol is used on the data port. Choose this 

based on the interface module protocol being used. 

NOTE: Intellikit modules only 

support the D2D protocol. All OmegaLink modules support BOTH protocols 

however, the ADS protocol is recommended for maximum capabilities.

User Feature Programming: Ignition on, off, press valet 5 times

# Feature

Lock Button Unlock button

Trunk button 

”START” button

1   Engine Run Time

10 min

5 min

15 min

20 min

2   Steady/Flashing lights for RS Steady

Flashing

3   Horn Honk Volume

Low

Hi

On Demand

OFF

4   Pulse Horn/Steady Siren

Pulsed Lo

Pulsed Med

Pulse Hi

Steady Siren

5   Doors Lock w/ Ign. ON

ON

OFF

6   Doors Unlock w/ Ign. OFF

ON

OFF

7   Unlock w/ Trunk Release

ON

OFF

Installer Feature Programming: Ignition on, off, press valet 10 times
1   RS Activation

1 press

2 presses

3 presses

4 presses

2   PINK/WHITE wire function

Ignition

Accessory

Start

3   Engine Detection

Tachless Hi

Tachless Lo

Tach Wire

Datatach

Crank Only (Press Lock +Unlock)

4   Gas or Diesel Engine

Gas

Diesel 

(15 sec delay)

Diesel  

(20 sec delay)

Diesel  

(30 sec delay)

5   Sat. Port Green Wire 

Starter

Pulse After Start Status

Domelight

6   Sat. Port Blue Wire

Status

Ignition

7   Crank Time

0.7 Sec

1.00 Sec

1.5 Sec

2.25 Sec

8   Doorlock Outputs

0.8 Sec

3 sec

Double Unlock

Total Closure

9   Remote Start Lock Control

Off

Lock After Start Unlock Before 

Start

Both

10   Turbo Timer

OFF

1 min

2 min

3 min

11   Manual Transmission RS

ON

OFF

12   Data Port Protocol

D2D (Trilogix) ADS (iData)

Summary of Contents for RS-350-EDP

















Reviews: