RS-360-EDPB
DELUXE KEYLESS REMOTE START SYSTEM
Transmitter/Controller Operations
:
LOCK/ARM
: Press and release “lock” once
UNLOCK/DISARM
: Press and release “unlock” once
TRUNK RELEASE/2ND CH
: Press “trunk” for 3 seconds
REMOTE START
: Press “start” twice in 5 seconds
(see user feature #8 for options)
PANIC
: Press “lock” or “unlock” for 3 seconds
3RD CHANNEL
: Press “trunk & start” for 3 seconds
4TH CHANNEL
: Press “lock” & “trunk” for 3 seconds
5TH CHANNEL
: Press “unlock” & “start” for 3 seconds
SILENT ARM/DISARM
: Press “trunk” twice in 5 seconds
SENSOR BYPASS
: Press “trunk” within 5 seconds of arming
the alarm
3
1
2
4
The 1-Way Transmitter
Part number: 1411-03
Battery: 1 x CR2032
Frequency: 433MHz
1. LOCK button
2. UNLOCK button
3. TRUNK button
4. START button
Feature Programming
:
1. Turn the ignition key “on, then “off”
2. Within 7 seconds of step 1, press the valet switch 5 times
(user features) or 10 times (installer features). This
siren/horn will sound.
3. Press the valet switch the number of times equal to the
feature number you wish to access.
4. Press the controller/transmitter button that corresponds to
the desired setting.
5. To change additional features, repeat steps 3-4.
6. To exit programming, turn the ignition key “on”, then “off”
or the system will exit automatically if there is a 10 sec-
ond delay between any steps.
Tach Learning Procedure
:
1. Turn the ignition key “on”
2. Within 10 seconds of step 1, press the brake pedal 5
times. The siren/horn will chirp 5 times.
3. Start the engine with the key. When tach is successfully
learned, the status light will turn on solid.
4. If you need to relearn a later tach signal due to cold start/
high idle, you can press the valet switch once to learn
the current tach signal. The status light will turn off and
back on to indicate it has relearned.
Programming Controllers/Transmitters
:
1. Be sure to have all controllers/transmitters present and be
sure the system is in a disarmed/unlocked state.
2. Turn the ignition key “on”.
3. Within 7 seconds of step 1, press the valet switch 5 times.
The siren/horn will sound.
4. Press LOCK on one transmitter/controller until you hear a
single chirp.
5. Repeat step 4 for each transmitter/controller to be pro-
grammed.
6. To exit programming, turn the ignition key “off” or the sys-
tem will exit automatically if there is a 10 second delay
between any steps.
Programmable Features Matrix
Technology
CONVENIENCE
SECURITY
INST
ALLER ONL
Y
User Feature Programming: Ignition on, off, press valet 5 times
# Feature
Lock Button
(Brake x 1)
Unlock button
(Brake x 2)
Trunk button
(Brake x 3)
Start button
(Brake x 4)
Lock + Unlock
(Brake x 5)
1 Remote Start Run Time
10 min
5 min
15 min
20 min
2 Flashing Light Confirmations
Unlock: ON
RS: ON
Unlock: ON
RS: Flash
Unlock: Flash
RS: ON
Unlock: Flash
RS: Flash
3 Confirmation Chirp Volume
Low
Med-Low
Med-High
High
4 BROWN Wire: Siren / Pulsed Horn
Pulse LOW
Pulse MED
Pulse HI
Steady Siren
5 Ignition Lock / Unlock
Off
Ign On = Lock Ign. Off = Unlock Lock + Unlock
6 Door Open Bypass for Feat. #5
On
Off
7 Unlock w/ Trunk Release
On
Off
8 RS Activation (Remote)
Start x 1
Start x 2
Start x 3
Start x 4
9 Last Door Arming
Off
On w/o Lock
On w/ Lock
10 Automatic Rearming
Off
On w/o Lock
On w/ Lock
Enhanced
11 Confirmation Chirps
Siren + Horn Siren Only
On Demand
Off
12 Anti-Carjacking
Ignition
Door
Ig Door
Off
13 Secure Code
Read Operation Guide For Programming Instructions
14 Ignition Override
On
Off
15 Alarm Trigger Duration
30 sec
60 sec
90 sec
120 sec
16 Arming Delay
3 sec
15 sec
30 sec
45 sec
17 Open Door Warning Upon Arming
On
Off
Installer Feature Programming: Ignition on, off, press valet 10 times
1 RS Activation (WHITE/BLUE wire)
1 Pulse
2 pulses
3 pulses
4 pulses
2 PINK/WHITE Wire
Ignition
Accessory
Starter
3 Engine Detection
Tachless Hi
Tachless Lo
Tach Wire
Data-tach
Crank Only
4 Gasoline or Diesel Engine
Gasoline
15 sec Diesel
20 sec Diesel
30 sec Diesel
5 Light Relay Function
Dome Light
Start
Ignition
Accessory
Status
6 Blue Sat Port BLUE Wire
Ignition
Status
Pulse After Start
below freezing
Pulse After
Engine Off
Horn
7 Crank Time
0.75 sec
1 sec
1.5 sec
2.25 sec
8 Door Lock/Unlock Outputs
0.8 sec
3 sec
Double Unlock
Total Closure
9 Remote Start Lock Control
Off
Lock after
Start
Unlock before
Start
Lock + Unlock
10 Turbo Timer
Off
1 min
2 min
3 min
11 Manual Transmission
On
Off
12 Data Port Protocol
Green: DBI
Black: DBI
Green: iData
Black: iData
Green: DBI
Black: iData
Green: iData
Black: DBI
13 Alarm Functions
On
Off
14 Pulse Ign. on Disarm
On
Off
15 Lock On Prewarn
On
Off
16 Starter Interrupt
Alarm Only
Anti-grind Only
Alarm/Anti-Grind
Automatic
17 Low Temp Crank Extender
0 ms
200 ms
300 ms
400 ms
18 Arm/Disarm or CH. 4/5
Arm/Disarm
Arm/CH. 5
CH. 4/Disarm
CH. 4/CH.5
19 Horn Relay Function
Horn
Ignition
Trunk Release
Pulse After
Start
20 Low Current/Motorcycle Mode
On
Off
