EXFO FTB-860 User Manual Download

Page: 190 / 409

Cable Test Setup and Results

178

FTB-860/880

Summary Results

MDIX (-)

: For 1Gbit/s, crossed pair with pair A swapped with pair B

and/or pair C swapped with pair D.

Noise:

Excessive noise on a pair most likely caused by a link

partner running in 10/100 Mbit/s forced mode. In this case, no
propagation delay or length is reported and there is no comparison
with any threshold.

Note:

For 1Gbit/s, both MDI and MDIX can be reported simultaneously since
crossed pairs detection is performed independently for pairs A-B and C-D.

When the link is down:

Short:

Short-circuit between Tip and Ring wires of a pair or Tip or

ring wire of a pair is connected with an alien wire grounded.

Open:

No cable plugged in, remote end open, or either one or two

wires of a pair are not connected.

Short-between-pairs:

Short between one or two wires of a pair

with one or two wires of another pair. Short between more than
two pairs, including one or two wires for each pair.

Noise:

Excessive noise on a pair most likely caused by a link

partner running in 10/100 Mbit/s forced mode. In this case, no
distance is reported and there is no comparison with any
threshold.

Unknown:

No fault has been identified but the link is down. To

maximize the cable test result, it is preferable to have the far end
equipment powered up.

Note:

Refer to

Ethernet Cables

on page 369 for cable pinout.



Distance To Fault (m/ft)

: Gives the distance to fault from the near end

for each pair, unless the problem is due to excessive noise. Noise may
be due to electrical noise causing communication error.

Summary of Contents for FTB-860


























































































































































































































































































































































































































Search results

Summary of Contents for FTB-860

Reviews:

Related manuals for FTB-860

Brands by name

Popular brands

EXFO FTB-860, User Manual

Search results

Summary of Contents for FTB-860

Reviews:

Related manuals for FTB-860

Brands by name

Popular brands