EXFO FTB-860 User Manual Download | Manualshive

Page: 371 / 409

background image

NetBlazer

359

23 Warranty

General Information

EXFO Inc. (EXFO) warrants this equipment against defects in material and
workmanship for a period of XX Number of Years XX from the date of
original shipment. EXFO also warrants that this equipment will meet
applicable specifications under normal use.

During the warranty period, EXFO will, at its discretion, repair, replace,
or issue credit for any defective product, as well as verify and adjust the
product free of charge should the equipment need to be repaired or if the
original calibration is erroneous. If the equipment is sent back for
verification of calibration during the warranty period and found to meet all
published specifications, EXFO will charge standard calibration fees.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT SHALL EXFO BE LIABLE FOR
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

I

MPORTANT

The warranty can become null and void if:



unit has been tampered with, repaired, or worked upon by
unauthorized individuals or non-EXFO personnel.



warranty sticker has been removed.



case screws, other than those specified in this guide, have been
removed.



case has been opened, other than as explained in this guide.



unit serial number has been altered, erased, or removed.



unit has been misused, neglected, or damaged by accident.

«
...
369
370
371
372
373
...
»

Summary of Contents for FTB-860


























































































































































































































































































































































































































Reviews:

No comments

Related manuals for FTB-860

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: Modulate Pages: 2

Brand: Parr Instrument Pages: 24

Brand: JBL Pages: 15

Brand: Vari Lite Pages: 14

Brand: Vaniman Pages: 3

Brand: ABB Pages: 4

Brand: Beurer Pages: 21

Brand: SCHUNK Pages: 35

Brand: Nautilus Pages: 2

Brand: Woods Pages: 54

Brand: Osprey Pages: 12

DIAGNOdent pen 2190

Brand: KaVo Pages: 2

Brand: Audio Precision Pages: 76

Brand: Inlight Pages: 2

Brand: ProFurl Pages: 40

Brand: TKO Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands