EXFO FTB-860 User Manual Download | Manualshive

Page: 395 / 409

background image

Glossary

NetBlazer

383

1588 PTP

If the Master Clock has sufficient capacity to handle the Client Clock
request, it responds with a signaling message containing a GRANT
UNICAST TRANSMISSION TLV.

The REQUEST UNICAST TRANSMISSION TLV contains several
parameters:



messageType

is the type of service being requested: Announce,

Sync, or Delay Response.



durationField

is the duration of the requested service:

300 seconds by default and configurable from 60 to 1000 seconds.



logInterMessagePeriod

: transmission rate of the requested

messages.

If the Master Clock denies the request, e.g. because it has no remaining
capacity, it will send back a GRANT UNICAST TRANSMISSION TLV with the
durationField set to zero.

In the event of being denied service by a Master Clock, or receiving no
response to the service request, a Client Clock should wait a minimum of
one second before issuing a new Unicast request to that Master Clock.

As Unicast service is only granted for a limited time, the Client Clock must
re-request service periodically, before the expiration of the current grant.
The Client Clock should reissue the request sufficiently far in advance of
the expiration to allow the request to be repeated at least twice if no grant
is received. This parameter is called Unicast renewal interval.

«
...
393
394
395
396
397
...
»

Summary of Contents for FTB-860


























































































































































































































































































































































































































Reviews:

No comments

Related manuals for FTB-860

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: Haag-Streit Pages: 18

Brand: Haag-Streit Pages: 20

Brand: V-TEK Pages: 2

Brand: V-TEK Pages: 112

Brand: jablotron Pages: 2

Brand: Pari Pages: 282

Brand: TDR Pages: 8

Brand: Össur Pages: 50

Brand: Össur Pages: 13

PRO-FLEX XC PXC0xyyz

Brand: Össur Pages: 68

Brand: Össur Pages: 25

Brand: Össur Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands