FTBx-88260
Power Blazer and NetBlazer
Getting Results
The
Summary
tab is automatically
displayed once the test is started.
Select a tab to get additional test
results.
Alarm/Error Injection
Test control buttons are
reconfigured according
to the test application
and status.
The
Stop
button is
displayed when the
test is running.
1
Tap the
Alarms/Errors
tab.
3
Tap
Inject
.
Gives more information on this alarms/errors group.
Hides the alarm/error selection.
Status Bar
Additional Status Bar Symbols:
Test Control Buttons
Connection established between two testing units in
Dual Test Set
(DTS),
EXFO|Worx Interop
, or in
Loop Up
mode.
Connection not established between two testing units in
Dual Test Set
(DTS),
EXFO|Worx Interop
, or in
Loop Up
mode.
Remote unit is busy (locked) in
EXFO|Worx Interop
operation mode.
LINK
: Port link
PTP
: 1588 PTP, PTP Frames
ESMC
: SyncE, ESMC Frames
(BTS)
CPRI, Base Station emulation mode
(RRH)
CPRI, Remote Radio Head emulation mode
Start
Stop
TX
Starts test. Available when the test is not running.
Stops test. Available when the test is running.
Enables traffic generation and starts test. Available with Traffic Gen & Mon and eCPRI BERT.
Save
Load
Saves, loads, imports, exports, and deletes configuration file(s). Available when the test is not
running.
Report
Saves, opens, imports, exports, and deletes test report(s). Available when the test is running or
stopped, but the report generation (save) is only possible when the test is stopped.
Laser
(on) Indicates that the laser control is on (for at least one Lane for parallel interface); the laser button
has a red border. Tapping this button will turn off the laser (for all Lanes for parallel interface). Only
available with optical ports.
Laser
(off) Indicates that the laser control is off (for all Lanes for parallel interface). Tapping this button will
activate the laser immediately by emitting an optical laser signal (on all Lanes for parallel
interface). Only available with optical ports.
Reset
Clears results, statistics, and logger content. Available when the test is running.
Inject
Injects alarms/errors based on settings from the Inject button from the Results - Alarms/Errors tab.
Discover
Remote
Discovers and connects to a remote module that loops back the traffic via Smart Loopback or
Dual Test Set (DTS).
Test
Direction
Pattern Synchronization
Power
Clock
Laser
Remote Control
Inject
Non-default OH
Interface/Signal
Port
Global Indicator
Tap anywhere within the global
indicator area to view the
maximized view of these
indicators.
The global indicator displays the pass/fail verdict,
global alarm, timer, and/or test duration.
2
Tap to select an alarm/error.
4
Select the alarm/error to
be injected and its
parameters.
Quick Reference Guide
HIGH-SPEED MULTISERVICE TEST MODULE
© 2019 EXFO Inc. All rights reserved.
Printed in Canada (2019-07)
P/N: 1075976
Version: 6.0.0.1
For more information,
refer to the user guide.
Physical Interfaces
Po
rt
1
/Po
rt
2
Connect the signal to the corresponding interface on the module. Insert an EXFO supported transceiver into the
port’s slot then carefully connect optical fiber cables to the transceiver IN (RX) and OUT (TX) ports. The
FTBx-88260 module with TA-SFP28 transceiver systems are shown below as examples for connector location
purposes.
Port A
Port B
FTBx-88260
1. Laser radiation is emitted from this port when LASER LED is on.
Port A1
1
TA-SFP28
Port A2
1
Port B1
1
Port B2
1
SFP28:
Ethernet 100/1000 Mbit/s, 10 Gbit/s, 25 Gbit/s optical
Ethernet 10/100/1000 Mbit/s electrical (using active copper SFP)
Fibre Channel 1X, 2X, 4X, 8X, 10X, 16X, 32X
eCPRI 10 Gbit/s, 25 Gbit/s
CPRI 1.2, 2.4, 3.1, 4.9, 6.1, 9.8, 10.1 Gbit/s
OBSAI 1.5, 3.1, 6.1 Gbit/s
OC-1/STM-0, OC-3/STM-1, OC-12/STM-4, OC-48/STM-16, OC-192/STM-64
OTU1, OTU2, OTU1e, OTU2e, OTU1f, OTU2f
QSFP+:
Ethernet 40 Gbit/s
OTU3e2, OTU3e1, OTU3
CFP4:
Ethernet 100 Gbit/s
OTU4
SMA:
Future use
SMB:
IN: 2 MHz, 10 MHz, 1PPS
OUT: 2 MHz
SMB:
IN: 1PPS
TA
-S
F
P
28
TA
-Q
SFP2
8
TA
-C
F
P
4
TA
-S
Y
N
C
Port 1
1
Port 2
1
Port
1
/Por
t
2
Por
t 1
REF OUT
SMA:
Eye diagram clock signal generation
EX
T
CLK
1
PPS
A
N
TENNA
QSFP28:
Ethernet 100 Gbit/s
OTU4
