background image

Channels Reverse

1.Turn the throttle stick to min position.

2.Power on the Transmitter and the receiver.

3.Do NOT unlock the throttle.

4.Turn the channel stick to max position of any side and hold for several seconds.

5. When you hear a “beep” sound, it means the channel is reversed.

WARNING: Normally this function is not necessary to be operated. Only operate

the below steps when you understand completely of the channel reverse function.

WARNING: Do NOT reverse throttle otherwise serious damage would cause!

 

Flight Checklist

Charging Instruction 

                                                                                        

1. Unplug the battery from your plane.

2. Carefully plug the charger into the USB port on your computer or USB adapter.

3. Connect battery into the charger.

4. The charging process takes about 3.5 hours. For safety reasons, never charge 

the battery for longer than 4 hours. While charging, the red LED indicator will be on. 

When charging is finished, the red LED will be off.

NOTE: This checklist is NOT intended to replace the content included in this 

instruction manual. Although it can be used as a quick start guide, we strongly 

suggest reading through this manual completely before proceeding.

- Always turn on the transmitter first.

- Ensure the throttle control stick is on the button position then plug the battery.

- Fly the model (hand launch or take off from a flat/level surface).

- Land the model (land on a flat/level surface).

- Unplug the Lipo flight battery from the ESC.

- Always turn off the transmitter last.

Summary of Contents for 768-1

















Reviews: