background image

 

 

APPLICATION CHART*  

 

Back-up Power of all electrical loads: 

 

Computer & Printers 

 

Fan, Tube lights, CFL, LED Lights 

 

T.V. Sets, DVD & Music System 

 
*ideal for computer & printer  
 
 
 

 

Where to install 

The system should be installed in a location that meets the following requirements: 
 

a)

 

Dry

 – Do not allow to water to drip or splash on the Exide Inverterz 

b)

 

Cool 

– The ambient air temperature around the system should be between 

0

0

C to 45

0

C (32

0

F to 113

0

F). Cooler environment is better for the system. 

c)

 

Ventilation: 

Allow at least two inches (5cm) of clearance around the system 

for air flow. 

d)

 

 Safe: 

 DO not install the Exide Inverterz in the same compartment as 

batteries or in any compartment which are storing flammable liquids such as 
gasoline.

 

e)

 

Close to battery - 

Install the system as close to the battery as possible in 

order to minimise the length of cable required to connect the system to the 
battery. It is better and cheaper to run longer AC wires than longer DC 
cables. 

 

CAUTIONS!  To prevent fire, do not cover or obstruct ventilation openings. Do 
not install the system in a zero - clearance compartment.  Overheating may 
result. 
 
WARNNING! This equipment contains components which tent to produce arcs 
or sparks. To prevent fire or explosion do not install in compartment 
containing batteries or flammable materials or in locations which require 
ignition protected equipment. 

 
 

 

Installation 

Summary of Contents for Inverterz GQP 12V 1450VA













Reviews: